Pioneer DJM-2000nexus Bedienungsanleitung Seite 26

REV ROLL
1 2
Original
Effect turned on
1/1 reverse
roll
Reversed and repeated
This function records the input sound at the point at which the [ON/OFF]
button is pressed, reverses the recorded sound and repeats it according
to the beat button's fraction.
Beat buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
EFFECT FREQUENCY
(parameter 4)
FILTER
1
This function changes the filter's cut-off frequency according to the beat
button's fraction.
Beat buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
EFFECT FREQUENCY
(parameter 4)
TRANS
1
MIN MAX
1/1 beat
Cut
MIN MAX
Cut
MIN MAX
EFFECT FREQUENCY
This function cuts the sound according to the beat button's fraction.
The amount of the sound to be cut can be changed at
[EFFECT FREQUENCY].
Beat buttons (parameter 1)
TIME control (parameter 2)
LEVEL/DEPTH control
(parameter 3)
EFFECT FREQUENCY
(parameter 4)
26
En
The effect time is set from 1/8 to 4/1 with respect to
1 beat of BPM time.
Use this to set the effect time.
10 to 4000 (ms)
Use this to set the balance between the original
sound and ROLL.
Use these to set the balance between the original
sound and the ROLL for the different bands.
Frequency
These set the cycle for moving the cut-off frequency
from 1/8 to 4/1 with respect to 1 beat of BPM time.
Use this to set the cycle at which the cut-off fre-
quency is moved.
10 to 32000 (ms)
The further the control is turned clockwise, the more
the effect is stressed.
The original sound is set when turned fully
counterclockwise.
These set the balance between the original sound
and the effect sound for the different bands.
Time
Cut
Cut
These set the 1/8 to 4/1 cut time with respect to 1
beat of BPM time.
Use this to set the effect time.
10 to 16000 (ms)
Sets the balance between the original sound and the
effect sound.
This sets the amount of the original sound to be cut
for the different bands.
PHASER
1
Phase shift
Cycle
The phaser effect changes according to the beat button fraction.
These set the cycle for moving the phaser effect by
Beat buttons (parameter 1)
1/8 to 4/1 with respect to the time of one BPM beat.
This sets the cycle by which the phaser effect is
TIME control (parameter 2) moved.
10 to 32000 (ms)
The further the control is turned clockwise, the more
LEVEL/DEPTH control the effect is stressed.
(parameter 3) When turned all the way counterclockwise, only the
original sound is output.
Use these to set the balance between the original
EFFECT FREQUENCY
(parameter 4) sound and the effect sound for the different bands.
GATE
1
Level
Threshold
MIN MAX
Threshold
MIN MAX
Threshold
MIN MAX
EFFECT FREQUENCY
This function outputs the input sound that has a level above the thresh-
old level, cutting the input sound that has a level below the threshold
level.
The threshold level can be changed at [EFFECT FREQUENCY].
Beat buttons (parameter 1) This sets the release time between 1 and 100 %.
This sets the release time.
TIME control (parameter 2)
1 to 100 (%)
Sets the threshold level.
LEVEL/DEPTH control
The further the control is turned clockwise, the more
(parameter 3)
the effect is stressed and the sound is cut.
Use these to set the threshold levels for the different
EFFECT FREQUENCY
(parameter 4) bands.
SEND/RETURN
1
SEND
RETURN
DJM-2000NXS
Connect an external effector, etc., here.
[EFFECT FREQUENCY] can be used as an isolator.
Beat buttons (parameter 1) —
TIME control (parameter 2) —
LEVEL/DEPTH control This adjusts the sound level input to the [RETURN]
(parameter 3) terminal.
This sets the audio output level of the RETURN
EFFECT FREQUENCY
(parameter 4) sound for the different bands.
1 When "A", "B" or "M" is selected with the [CH SELECT] buttons, the
effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT)
unless the sound for the channel you want to monitor is being output
from [MASTER] channel.
2 When BEAT EFFECT is off, the effect sound cannot be monitored by
pressing [CUE] (BEAT EFFECT).
Time
Time
Effector