Herunterladen Inhalt Inhalt Diese Seite drucken

Pioneer DJM-2000nexus Bedienungsanleitung Seite 17

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Effect Name
Descriptions
NOISE
Sound is created inside this unit, mixed to the sound
of the channel selected in the [CH] section, then
HI-HAT
CLAP
output according to the [TRIGGER CH (SAMPLING/
SNARE
TRIGGER CH)] trigger.
The sound of the channel selected at [TRIGGER CH
(SAMPLING/TRIGGER CH)] is sampled, mixed to
SAMPLER
the sound of the channel selected in the [CH] sec-
tion, then output according to the [TRIGGER CH
(SAMPLING/TRIGGER CH)] trigger.
The pitch of the sound of the channel selected in
the [CH] section is changed, mixed with the channel
PITCH
selected in the [CH] section, then output according
to the [TRIGGER CH (SAMPLING/TRIGGER CH)]
trigger.
The sound input at [CH] is output according to the
GATE
[TRIGGER CH (SAMPLING/TRIGGER CH)] trigger.
! It is not possible to select multiple effects simultaneously.
4 Press [TRIGGER (SAMPLING/TRIGGER)].
The [TRIGGER] menu appears.
5 At [TRIGGER CH (SAMPLING/TRIGGER CH)], select
[CH3].
This selects the channel to be used as the effect trigger.
! When [SAME] is pressed, the same channel as the one selected in
the [CH] section is selected as the trigger.
6 At [TRIGGER BAND], press [MID] and [HI].
This selects the frequency band set as the effect trigger.
Only [LOW] (the bass sound) is selected.
7 Press the [ON/ OFF] button.
This turns the effect on.
The [ON/ OFF] button flashes when the effect is on.
8 Touch the control area.
[
] appears at the point at which the panel was touched.
The [CH3] sound at the point in the control area that was touched is
sampled.
Triggered by the low frequency sound of [CH3], the sampled sound is
mixed with the sound of [CH2] (which is continuing to play normally) and
output from the [MASTER] terminals.
The effect changes when the position touched in the control area is
changed.
! When the [ON/ OFF] button is pressed again, the effect turns off.
! The sampled sound is only valid while the control area is being
touched.
! To switch from the [SIDECHAIN REMIX] to the [FREQUENCY MIX]
mode, first press the [ON/OFF] button to turn the effect off, then
press [MIX].
 Using [HOLD]
When [HOLD] is turned on, effect's parameter information is held even
if the effect is turned off. The parameter information is cleared when
[HOLD] is turned off.
! The parameter information and sampled sound are cleared when the
effect is switched.
LIVE SAMPLER
The sound input to the [MIC] terminal or the sound output from the
[MASTER] terminals can be sampled and played on a PRO DJ LINK–
compatible Pioneer DJ player.
Connect this unit and PRO DJ LINK-compatible Pioneer DJ player in
advance. For instructions on connections, see Connecting input termi-
nals on page 7.
SOURCE SELECT
Select the source to be sampled here.
1
Use these to adjust the volume for recording.
REC VOLUME
The volume can be adjusted in the range –9 dB to +9
2
dB.
This indicates this unit's status and whether or not
Status indicator
3
sampling data is available.
Waveform display
This displays the sound as a waveform.
4
Playing address
This displays the sound as a bar graph.
5
display
This is only displayed when previewing the sound.
The sound is played from the position at which the
Slider
touch panel was touched.
6
This is only displayed when previewing the sound.
The sound is sampled from a point 8 seconds before
PRE-REC SAVE
7
the button was pressed.
The sound is sampled for up to 8 seconds from the
REC (REC STOP)
8
point at which the button is pressed.
Use this to preview the sampled sound over the
PREVIEW (STOP)
9
headphones.
 Sampling the sound being played
1 Press [LIVE SAMPLER].
The [LIVE SAMPLER] screen appears on the touch panel.
2 Press [MIC] or [MASTER] in the [SOURCE SELECT].
This selects the channel to be sampled.
3 Press [REC (REC STOP)].
The sound of the channel selected at step 2 is sampled from the point at
which [REC (REC STOP)] was pressed.
! Sampling is possible for up to 8 seconds.
! Sampling stops automatically once 8 seconds have elapsed after
[REC (REC STOP)] was pressed.
4 Press [REC (REC STOP)].
Sampling stops. The sample saving screen is displayed.
 Sampling the sound from the point 8 seconds
before
1 Press [LIVE SAMPLER].
The [LIVE SAMPLER] screen appears on the touch panel.
2 Press [MIC] or [MASTER] in the [SOURCE SELECT].
This selects the channel to be sampled.
3 Press [PRE-REC SAVE].
The sound for the channel selected in step 2 is sampled from the point 8
seconds before [PRE-REC SAVE] was pressed.
! Sampling is possible for up to 8 seconds.
 Previewing the sampled sound
1 Press the [CUE] button to the left of the touch panel.
2 Press [PREVIEW (STOP)].
The position being played is displayed at the playing address and slider
displays.
! When the touch panel's slider is touched, the sampled sound is
played from that position.
1
2
3
4
5
6
7
8
9
17
En

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Djm-2000nxs

Inhaltsverzeichnis