Changing The Settings; Setting Preferences; About The Auto Standby Function - Pioneer DJM-2000nexus Bedienungsanleitung

Changing the settings

Setup item button
1

Setting preferences

Settings indicated in italics are the default settings set upon purchase.
Mode Options settings
MIDI
USER SETUP
FADER START
LCD
VERSION No.
QUANTIZE
SYSTEM
MIC
CLUB SETUP
TOUCH PANEL
PEAK LIMITER
FACTORY RESET
1 Changes the MIDI settings of the buttons on the control panel, [FREQUENCY MIX] and [SIDECHAIN REMIX].
2 Changes the MIDI settings for [TYPE A] to [TYPE D] on the MIDI control screen.

About the auto standby function

When [AUTO STANDBY] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions below met.
— That none of this unit's buttons or controls are operated.
— That no audio signals of –10 dB or greater are input to this unit's input terminals.
— That no PRO DJ LINK connections are made.
! The standby mode is canceled when [LIVE SAMPLER (UTILITY, WAKE UP)] is pressed.
1
Selection
Selection item 1
item 2
BUTTON ACTION
ZONE11
MIDI CHANNEL
BUTTON ACTION
ZONE22 MIDI CHANNEL
RESET
LINK CH1 to CH4
CONTROL CH2, CH3
BACK LIGHT 1, 2, 3, 4, 5
— —
QUANTIZE ON, OFF
–19 dB, –15 dB,
DIGITAL OUT MAX LEVEL
–10 dB, –5 dB
DIGITAL SAMPLING RATE 48 kHz, 96 kHz
AUTO STANDBY
ON, OFF
OUTPUT TO BOOTH
ON, OFF
MONITOR
TALK OVER THRESHOLD –25 dB, –20 dB,
LEVEL –15 dB, –10 dB
–25 dB, –20 dB,
TALK OVER LEVEL
–15 dB, –10 dB
— —
PEAK LIMITER
ON, OFF
—
YES, NO
1 Press [LIVE SAMPLER (UTILITY, WAKE UP)] for at least
1 seconds.
The [USER SETUP] mode setting screen is displayed.
The [LIVE SAMPLER (UTILITY, WAKE UP)] indicator flashes.
! To display the [CLUB SETUP] screen, first turn this unit's power
off, then press [POWER] while pressing [LIVE SAMPLER (UTILITY,
WAKE UP)].
2 Press the setup item button.
The selection items appear.
3 Select the setup item.
Select the item on the touch panel and enter it.
4 Change the item's setting.
Select the item on the touch panel and enter it.
! Press [SAVE] to save the changes to the [CLUB SETUP] screen.
5 Press [EXIT].
Close the [USER SETUP] mode setting screen.
! To close the [CLUB SETUP] mode setting screen, press the [POWER]
button to turn this unit's power off.
Selection item 3 Descriptions
TOGGLE
Select the MIDI signal sending method, [TOGGLE] or
[TRIGGER].
TRIGGER
1, 2, to 16 Sets the MIDI channel.
TOGGLE
Select the MIDI signal sending method, [TOGGLE] or
[TRIGGER].
TRIGGER
1, 2, to 16 Sets the MIDI channel.
Restores the [TYPE A] – [TYPE D] MIDI settings to the
—
default values. [RESET] function is unique to [ZONE2].
Turns the fader start function on and off for all DJ players
ON, OFF
connected to the [LINK] terminals.
Turns the fader start function of the DJ players connected to
ON, OFF
the [CONTROL] terminals on and off.
— Adjusts the touch panel's brightness.
— Displays this unit's software version.
Turns use of the beat information obtained from the player
—
on and off.
Sets the maximum level of the sound output from the
—
[DIGITAL OUT] terminals.
— Sets the digital signal's sampling rate.
— Turns the auto standby function on and off.
Sets whether or not to output the microphone's audio signals
—
from [BOOTH] terminals.
Sets the talkover sensitivity. The talkover function is activated
— when a sound with a volume above the set volume is input to
the microphone.
Sets the attenuation level for the sound other than the micro-
—
phone's sound when the talkover function is activated.
The touch panel's calibration is adjusted by pressing [+] in
—
order.
Alleviates sudden, unpleasant digital clipping of the master
—
output.
— Restores all the settings to their factory defaults.
1
En
27