Operating Hints - Grundig PA 2 Betriebsanleitung

Operating Hints

Note: This chapter contains excerpts from the operating instructions of the units. For further particulars please refer to the appropriate user instructions the part number of which is
indicated in the relevant spare parts list.
INSTALLATION PA 2
MOUNTING THE SPEAKER TO THE WALL
• Drill two holes in the wall using the supplied template as a reference for the
distance between the two holes.
• Insert the plugs and afterwards the screws.
• Now, you can mount the speaker on the two screws.
SETTING UP SPACE FIDELITY
Space Fidelity is very good-natured, and you can stand it almost anywhere to
enjoy superb sound. But if you want to feel the full force of this exciting system,
give the speaker a little 'breathing space'.
• Give the speaker one-and-a-half to three metres of free space on both sides.
• Do not place the speaker on the floor but mount it to a wall as described
above.
• Ensure that sufficient ventilation is available. An open space of 3 cm at the
top of the speaker is required.
• Then move back, sit back, and experience it. The most exciting sound you
ever heard.
CONNECTION OF THE SPACE FIDELITY SPEAKER
• The plugs of the speaker cable must be connected to the SPACE FIDELITY
output sockets on the back of your unit.
• Connect the white plug of the speaker cable to the white socket, the red plug
to the red socket and the black plug to the black socket.
SPACE FIDELITY
CONNECTION
INSTALLATION PA 3
SETTING UP SPACE FIDELITY
Space Fidelity is very good-natured, and you can stand it almost anywhere to
enjoy superb sound. But if you want to feel the full force of this exciting system,
give it a little 'breathing space'.
• Give it one-and-a-half to three metres of free space on both sides.
• Stand it off thirty centimetres from the wall.
• Then move back, sit back, and experience it. The most exciting sound you
ever heard.
MOUNTING THE WINGS ON SPACE FIDELITY
The wings are supplied with Space Fidelity PA 3 II and available as an
accessory for Space Fidelity PA 3 I.
• Mount the wings on the system as shown below.
1 2 3 4 5 6 7 HEADPHONES
DISC SELECT
• In case you do not wish to mount the wings, you may also insert the
supplied knobs that cover the holes in the side of your system.
1 2 3 4 5 6 7 HEADPHONES
DISC SELECT
• If you wish to remove the knobs again, the best way to do this is pressing
them forward or backward with your thumb and pulling them out.
INSTALLATION PA 3
MOUNTING SPEAKER COVERS TO THE TUBE
• Mount the speaker covers to the tube as shown in the illustrations below.
TUBE CONNECTION
• Connect the plug of the tube to the plug of the cables coming out at the back
of your unit.
• Insert the tube in your unit as shown in the illustration until it clicks in place.
Make sure that the connection cable is put behind the tube in the system.
To disconnect the tube, insert the two supplied tools as shown, and take the
tube out of your system.
INSTALLATION
POWER SUPPLY CONNECTION
• Only connect the unit to a 230V~, 50/60 Hz a.c. power source.
• Always ensure that the voltage indicated on the unit's rating plate agrees with
you local power supply. If this is not the case, consult your dealer or
customer service center. The rating plate is found on the back of the unit.
CONNECTING OTHER EQUIPMENT
Before connecting any other programme sources, always switch off Space
Fidelity. In addition, note the correct connection of the stereo channels:
R: right (red)
L: left (white).
AUX IN/OUT Connect the LINE OUT sockets of your other equipment, e.g. tape
-or DAT recorder, TV, DSR tuner, etc. to the sockets AUX IN.
Connect the LINE IN sockets of your other equipment, e.g. tape -
or DAT recorder to the sockets AUX OUT.
ANTENNA CONNECTION
FM
FM 75 AM LOOP ANTENNA
Only a good antenna system (broadband cable connection to your own antenna
system, or a common house antenna system) can guarantee optimum reception
quality, especially for FM stereo broadcasts.
FM 75 Ω
• The FM 75 Ω socket is used for connection to the Community or Cable An-
tenna System or to a roof-mounted FM antenna with an impedance of 75 Ohm.
• If non of these are available, you may use the cast (wire) antenna supplied for
nearby station (reception could be poor). You should not, however, change
the length of the cast antenna.
AM LOOP ANTENNA
• For AM reception, connect the supplied wires to the AM LOOP ANTENNA
terminals and position the antenna for best reception.
• The elevated antenna b as well as earth e can also be connected to these
sockets in place of the frame antenna.
Note: do not place the AM loop antenna on the unit, as this unit employs a
computing device which could cause interference.