Inhaltsverzeichnis
Werbung
OPERATION
SWITCHING ON AND OFF
• When you want to switch Space Fidelity on, press the POWER button. The
green LED in the button indicates that the unit is on.
button depressed:
POWER ON
button not depressed: POWER OFF
– The system will be activated and the source that was chosen before the
power was switched off will be selected again.
– If the system had been switched to standby before it was switched off, the
standby mode will be selected when the power is switched back on.
– When the system is switched to active mode (as described below), the
respective source will be indicated on the display.
– The sound is muted for approximately 3 seconds when it is turned on in
order to suppress disturbing initial signal noise.
• To switch off Space Fidelity press the POWER button again.
STAND BY
y
• You can switch the system to STAND BY with the
key on the remote con-
trol.
– STAND BY mode is indicated by the green LED in the POWER button.
• When you want to switch your system on again, simply press CD, TUNER,
TAPE or AUX on the remote control (or the SOURCE key on the top of your
unit).
Note:
In order to keep power consumption below 1 W a stand-by transformer has
been built in.
The choise for this option is a consequence of Grundig's environmental policy
targeting to reduce unnecessary power consumption.
SOURCE SELECTION
• To select a listening source, press CD, TUNER, TAPE or AUX on the remo-
te control (or the SOURCE key on the top of your unit). The respective sour-
ce will be indicated on the display.
VOLUME
• The volume can be adjusted with + and –
keys on the remote control.
• The volume level can also be controlled
with the + and – keys on the top of you
unit.
– The display shows the level from 0 - 63.
MUTING
• The volume can be completely muted by pressing the
key on the remote
control.
– This is useful, for example, if you want to take a telephone call and do not
want to be distracted by music, news, etc., from your system.
– If the muting function is used when recording a tape, this has no effect on the
subsequent recording volume level as only the speakers are muted.
The
indication lights up on the display when the MUTING function is
active.
• The MUTING function can be deactivated by pressing the
key again or by
pressing the VOLUME +/- key or any one of the input selection keys.
SOUND CONTROL
POWER SOUND
• With the POWER SOUND key you can switch to three sound settings as
follows: POWER SOUND ™ FLAT ™ USER ™ POWER SOUND.
POWER SOUND: slightly accentuates the lower and higher frequencies
which renders a more balanced overall sound during quieter passages.
Its effectiveness depends in turn on the setting of the volume knob. The
sound is thus optimally adapted to human hearing sensitivity, which is also
dependent on the respective volume.
FLAT : The bass and treble settings are switched to neutral. This function
merely bypasses the signal path through the bass and treble controls
ensuring that the original sound is reproduced with the highest fidelity.
ACTUAL : you will hear the actually selected sound preset: JAZZ, DISCO,
VOCAL, USER 1, USER 2, USER 3. See description below.
DISPLAY BRIGHTNESS
The display is automatically switched to normal brightness whenever the unit is
activated.
• To adapt the display brightness, select first SOUND CONTROL.
• Pressing the key changes the display brightness to 50%, pressing again
switches the display off.
• Press the key once more to return to normal display brightness.
BASS AND TREBLE
You can individually adjust the higher and lower frequencies from the sound of
your speakers. In this way, you can compensate for surrounding acoustic
irregularities which may be caused, for example, by sound reflection behaviour
on walls with relatively large, empty surface areas, or "damping" caused by fur-
niture or other objects.
You can adjust the bass and treble values as follows:
• Select the SOUND CONTROL mode.
• Then, press the MODE key
• Adjust now the TREBLE value with the 3 / 4 keys and adjust the BASS value
with the + / – keys
– The display shows the selected value e.g. TREBLE +8
SOUND PRESETS
The SOUND PRESETS selection mode is selected by selecting first SOUND
CONTROL and then the 3 / 4 keys
Space Fidelity is supplied with 3 preprogrammed sound presets: JAZZ,
DISCO and VOCAL.
Programming user presets
You also have the possibility to program 3 sound presets yourself: USER 1,
USER 2 and USER 3.
For these three sound presets you can install different BASS and TREBLE
values:
• Adapt the BASS and TREBLE values as described above.
• Then, press MEMORY.
– The display shows shortly USER 1.
• In the same way you can store USER 2 and USER 3.
Deleting a user preset:
• Select the sound preset (USER 1, 2 or 3) to be deleted by pressing the
3 / 4 keys.
• Press CANCEL.
– The sound preset is now deleted and can not be selected anymore with the
3 / 4 keys.
RADIO
(press TUNER to select radio mode)
SELECTING TUNER
– The first time you select TUNER, it automatically switches to 'FM', and the
display indicates 87,50 MHz. STEREO
is also selected.
– Your unit is provided with the function 'LAST STATION MEMORY', which
means that the station that was playing when the set was switched off will be
selected again when the tuner is switched back on.
SELECTING THE WAVE BAND
• To select the waveband, press MODE and within 3 seconds the + / – keys.
You can select the wavebands: FM - STEREO, FM - MONO and MW.
– The display shows the selected band.
– If you have selected FM - STEREO,
your unit is in stereo reception mode,
which means that as soon as a stereo sig-
MHz
nal of sufficient strength is detected, '
'
appears in the display. If stereo reception is disturbed, '
' disappears. In
this way, disturbing background noise is suppressed.
• If noise-free stereo reception is not possible, you can switch your unit to
MONO reception. In this case, select FM MONO.
The muting function is always switched off for MONO reception, allowing the
unit to receive even very weak broadcast signals.
ADAPTING THE ANTENNA (ANTENNA/CABLE)
If you receive broadcasts via broad band cable of a public or private cable servi-
ce, there may be high signal inputs at your antenna terminal, which may in turn
cause reception disturbances.
• If this is the case, press the MODE key and within 3 seconds 3 or 4 to switch
on the input attenuator CABLE appears on the display. This reduces the antenna
input sensitivity, thus reducing disturbances. This setting is automatically stored.
RDS RADIO DATA SYSTEM
Your tuner is an RDS tuner.
RDS (Radio Data System) stands for a new generation of radios that provides the
listener/user with more comfort and better reception in the short term, but also
opens up completely new information options for the future. RDS-equipped
receivers identify the tuned station (if it transmits 'RDS signals') and indicate
the name of the programme in the display (e.g. BAYERN 3, SDR 3).
If you are tuned to an RDS station, the name of the station will be indicated after
a short time.
For more information, please see page 28.
AUTOMATIC STATION SEARCH
• To activate automatic station search (AUTO TUNING), press Q or R
until the frequency display begins 'to run'; then release the key.
– The search stops as soon as a station with sufficient reception quality is
found and tuned to precisely.
The
indication lights up.
– Every time you begin a search, the unit
automatically switches to FM - STEREO.
– The frequency of the received station is indi-
MHz
cated in kHz (MW) or MHz (FM).
– If the search stops, the 'AUTO COMPARE' function first verifies whether the
station which has been found is already stored in the station memory. If this
is the case, the memory location of the station is displayed, as well as the
name of the station, if it already exists.
– Stations which are received with a weak field strength may be skipped.
These can be tuned to manually.
• If desired, you can also interrupt the search by pressing Q or R.
MANUAL STATION SEARCH (MANUAL TUNING)
• Briefly press the Q or R key to tune in the corresponding direction in
individual steps (FM: 25kHz; MW: 1 kHz).
• If you keep the key depressed, you can rapidly scan large frequency ranges.
When you release the key, AUTO TUNING is automatically switched to.
Muting is active during AUTO TUNING.
• If you briefly press one of the Q or R keys, manual tuning is automa-
tically switched to.
STATION MEMORY
59 memory locations are available for storing stations.
• Tune to the station you want to store with the station search function or
manually.
• Press MEMORY.
– The station is stored at the next available memory location.
MHz
– The tuner software first checks the station memory for available memory
locations. If all the locations are occupied, MEM FULL appears on the dis-
play for approx. 1.5 seconds.
– Assigning a station frequency to two different memory locations is not possi-
ble. The selected station is stored at the lowest available memory location,
meaning that you need not enter a number for memory locations.
– Every time the settings STEREO/MONO and ANTENNA/CABLE are changed,
they are automatically stored.
STORING STATIONS
• If you want to store a station, press MEMORY.
– The first station which is stored is assigned to memory location 1, the
second station to memory location 2 and so on.
• If you want to move a stored station to another memory location, press
MEMORY.
– The station is always assigned to the first available memory location.
• Pressing the key again assigns a station to the next available memory locati-
on.
Example:
You want to move your favourite station from memory location '6' to memory
location '1'.
• Select memory location '1'.
• Press CANCEL once.
– This deletes, or clears, memory location '1'.
You can also press MEMORY to move the station on location '1' to the next
available free memory location.
• Now select position '6', your favourite station, and then press MEMORY.
Your station is now stored on memory location '1'.
'LAST STATION MEMORY'
LAST STATION MEMORY means that the unit 'remembers' the last station that
was tuned to. This function ensures that the station which was selected before
the tuner was switched off is automatically selected again when your tuner is
switched back on.
Werbung
Inhaltsverzeichnis
