Communication Conditions - Sharp PG-B10S Anleitung
Vorschau ausblenden
Andere Handbücher für PG-B10S:
- Serviceanleitung (138 Seiten) ,
- Bedienungsanleitung (82 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PG-B10S
RS-232C Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
sold separately) to the projector. (See page
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digit
Response code format
Normal response
O
K
Return code (
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after
the power has been turned on, and then transmit the commands.
• When more than one code is being sent, send each command only after the response code for the previous
command from the projector is verified.
Commands
Example: When turning on the projector, make the following setting.
Computer
P
O
W
R
_
_
CONTROL CONTENTS
COMMAND PARAMETER
Standby
P
O
W
R
Power On
P
O
W
R
INPUT1
I
R
G
B
INPUT2
I
V
E
D
INPUT3
I
V
E
D
INPUT1 SIGNAL TYPE : AUTO
I
A
S
INPUT1 SIGNAL TYPE : RGB
I
A
S
INPUT1 SIGNAL TYPE : COMPONENT
I
A
S
Lamp Usage Time (hour)
T
L
T
T
Remaining Lamp Life (Percentage)
T
L
T
L
Lamp Status
T
L
P
S
Unit Status
T
A
B
N
Model Name Check
T
N
A
M
AV Mute Off
I
M
B
K
AV Mute On
I
M
B
K
Auto Sync Start
A
D
J
S
Note
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a
value in the range indicated in brackets under CONTROL CONTENTS.
54
for connection.)
Parity bit: None
Stop bit: 1 bit
Flow control: None
Parameter 4-digit
Problem response (communication error or incorrect command)
E
0DH
)
→
_
1
O
←
RETURN
_
_
_
0
OK or ERR
_
_
_
1
OK or ERR
_
_
_
1
OK or ERR
_
_
_
1
OK or ERR
_
_
_
2
OK or ERR
I
_
_
_
0
OK or ERR
I
_
_
_
1
OK or ERR
I
_
_
_
2
OK or ERR
_
_
_
1
0~9999
_
_
_
1
0~100
_
_
_
1
0:Off, 1:On, 2:Retry, 3:Waiting, 4:Lamp Error
_
_
_
1
0:Normal, 1:Temp High, 2:Fan Err,
4:Filter or lamp Cover Err, 8:Lamp Life 5% or less,
16:Lamp Burnt-out, 32:Lamp Not Lit,
64:Temp Abnormally High
_
_
_
1
PROJECTOR NAME
_
_
_
0
OK or ERR
_
_
_
1
OK or ERR
_
_
_
1
OK or ERR
16
0DH
Return code (
)
R
R
0DH
Return code (
)
Projector
K
- Quicklinks:
- Bedienungsanleitung
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
