Environmental Conditions; Converting An Existing Fireplace - EcoSmart XL Series Installationshandbuch

Clearances & Installation

Environmental Conditions

EcoSmart™ Fire Burners can be used both indoors and outdoors. When used indoors there must be a
minimum of 1500mm [59.1in] between the mouth of the flame and the nearest combustible at all times.
Make sure your fire is at least this distance away from curtains, etc. Be aware of drafts.
WARNING: Keep fire at least 1500mm [59.1in] away from any combustibles.
When used outdoors it is important that the model be positioned in a large open space ensuring that the
nearest combustible (trees, branches, umbrellas, ceilings etc) are a minimum of 2000mm [78.74in] away
in all weather conditions (for example, on windy days where there is movement in branches, the clearance
must still be met). When not in use it is recommended that you protect the model from water damage or
corrosion by covering. Protective covers are available for some models.
Installation
There are many different variations available for installing the Burner. In
all cases, the Burner must be:
- Installed into non-combustible material ONLY – for example stainless
steel, concrete, brick, stone
- Installed after all gas connections or pipelines in the area are
disconnected and made safe by an appropriately qualified and
licensed professional
- Installed and operated in a fixed and secure position before filling,
lighting and operating. Burners are not meant to be moved because
movement creates the risk of accidental fuel spillages. If you move
the Burner, make sure no fuel was spilled before you ignite the
Burner.
- Models from each range (grate/renovator/designer/outdoor) have
varied installation requirements. Be sure to refer to the specific
section of the manual for the detailed requirements of the model
purchased.
The best location for your Fire will be one that is:
- In a large, open space at least 1500mm [59.1in] away from any
combustible materials, such as curtains, wallpaper, veneer, etc.
- On a level floor – the floor can be made of any material.
- In a firebox made of non-combustible materials, such as steel,
concrete, brick, or stone.
- Positioned so that any accumulation of weather debris/pooling of
water is eliminated
- NOT INSTALLED DIRECTLY BESIDE OR NEAR WALLPAPER,
LAMINATE, VENEER OR ANY SURFACE THAT HAS NOT BEEN
FIRE RATED (THE HEAT WILL IMPACT THE MATERIAL). REFER TO
PRODUCT SPECIFICATION OF WALLPAPER, LAMINATE, VENEER
OR GLUE FOR HEAT TOLERANCES
- Installed into a setting that has a straight back – the incorporation of
angled backs alters the aerodynamics of the flame environment and
could lead to an unstable flame behaviour
- Fitted within a Top Tray which is not more than 200% the size of the
total Burner size.
Note that:
- Any furniture items or fittings directly above or beside the Burner
installation must be deemed suitable for heat tolerances by
their manufacturer e.g electronic items including screens and
entertainment equipment, wallpaper, laminates, veneers, glues,
reconstituted materials
- A heat reflective panel made of non combustible material (ideally
stainless steel) must be installed as the surround and top of the
fireplace setting to assist in heat distribution. The Fire Company Pty
Ltd is not liable for any injuries or damages sustained through the
use of panels not manufactured by The Fire Company Pty Ltd
- Glass or mirrored surfaces near the Burner installation must be
toughened.
- In some countries national or rural restrictions may apply and/
or approvals from building authorities may be required. Please
ensure you contact the appropriate parties before installing your
EcoSmart™ Fire.
WARNING! FIRE HAZARD. BURNERS HAVE BUILT-IN SPACERS ON
ALL EXTERNALSIDES. DO NOT PACK THESE WITH INSULATION OR
OTHER MATERIALS. THE AIR SPACES ARE NEEDED FOR PROPER
VENTILATION OF THE BURNER.
As noted in warning 2ii, a fire extinguisher is strongly
recommended.

CONVERTING AN EXISTING FIREPLACE:

If inserting an Burner into an existing masonry fireplace, adjust the
damper within the existing fireplace in order to keep the heat from
escaping through the flue.
© Copyright 2004 - 2011 The Fire Company Pty Ltd. All rights reserved. V8 090911
e.g Cyl, from Outdoor Range