Putting Into Operation; Working Instructions - Bosch ANGLE EXACT 6 Bedienungsanleitung

Type 0 602 490 639 / ... 640
Pull the insertion tool 1 off of the tool holder 2 with the
aid of pliers, if necessary.
Suspension Device
With the hanging hoop 8, the machine can be at-
tached to a suspension device.
Place the hanging hoop 8 included as an accessory on
the machine and allow it to engage in the slots 15.
Regularly check the condition of the hanging hoop and
the hook of the suspension device.

Putting into Operation

When starting the power tool, you should first select
the direction of rotation with the right/left rotation
switch 14 since the power tool starts only when the
right/left rotation switch 14 is not in the middle position
(switch-on lock).
Setting the Direction of Rotation
Right rotation: Press the right/left rotation switch 14 to
the left to the stop (Screwing in of
screws).
Left rotation: Press the right/left rotation switch 14 to
the right to the stop (Loosening or un-
screwing of screws).
Operate the right/left rotation switch 14
only when the power tool is at a stand-
still.
Switching on the LED Work Area Illumination
Lamp
The work area lamp 21 makes possible the lighting of
the screwing position for unfavourable light conditions.
The work area lamp 21 is switched on by lightly press-
ing the on/off switch 13. When the on-off switch 13 is
firmly pressed, the power tool is switched on and the
work area lamp 21 continues to light.
Do not look directly into the work area
lamp – your sight can be temporarily de-
graded!
3 609 929 879 • (03.02) T
14
Switching On/Off
The tools have a torque dependent switch-off cou-
pling that is adjustable in the specified range. It re-
sponds when the torque that is set is reached.
Switching on: Press the on/off switch 13 to the stop.
Switching off: Release the on/off switch 13.
When the on/off switch 13 is released prema-
turely, the pre-set torque is not reached.

Working Instructions

Remove the battery from the power tool before ad-
justments are made to the tool, accessories are
changed or the tool is stored. This safety measure
prevents the unintentional switching on of the power tool.
Removing the Battery
The battery 11 is located in the handle of the power tool.
Press the unlocking buttons 12 on both sides and pull
the battery 11 downward out of the handle. Do not use
force.
Setting the Torque
The tightening torque is dependent on the spring pre-
tension of the switch-off coupling. The switch-off cou-
pling responds in right as well as left rotation when the
torque setting is reached.
For setting the individual tightening torques, use only
the adjustment tool 23 provided (Fig.
Push the slide 7 on the power tool completely back. In-
sert the Allen key 24 into the insertion tool 1 and turn
slowly until a small indentation in the coupling is visible
in the opening in the housing (Fig.
justment tool 23 into this indentation and turn the ad-
justment tool 23.
Turning in the clockwise direction results in a higher
torque, in the counter clockwise direction, a lower toque.
Note: The required adjustment is dependent on the
type of threaded connection and can be best deter-
mined by practical trials. Check the trial screwings with
a torque wrench.
Set the torque only in the specified per-
formance range, otherwise the shut-off
coupling will no longer respond.
Marking the Torque Setting
To identify individually adjusted tightening torques, the
marking ring 18 can be replaced with a marking ring of
another colour. Press off the marking ring 18 with a
thin screwdriver blade, a knife or similar.
Always use the power tool with a marking ring since
otherwise the housing is no longer closed.
English–6
The tool switches off automatically
when the adjusted torque setting is
reached.
C
).
B
). Insert the ad-