Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6.3 LCD-display
If the CD is improperly positioned,"ERR" or "NO DISC" appears on the display.
If the CD is properly positioned, the CD-player reads the CD.
By pressing the SGL/CTN-button, the CD-player is put into Single-mode and the display shows "SINGLE".
The indication "0.0" means that the playback-speed has not been changed. If you adjust the playback-speed
via the Pitchfader (Pitch-LED of the selected speed is flashing), the respective percentage is indicated in the
display.
6.4 Play/Pause
In the Pause-mode the the time-indication in the display stands still and the Play/Pause-LED flashes. The
playback of the first track can be started by pressing the Play/Pause button. In the Playback-mode, the time-
indication in the display is running and the Play/Pause-LED shines permanently.
If you wish to interrupt the playback, press the Play/Pause-button and the laser stops at the position where
you stopped.
6.5 Selecting a track via the Track-buttons
You can select the desired track via the Track-buttons.
In order to play a track from the beginning, press the Track-buttons until the desired track number is
displayed. If you hold the respective Track-button, the CD-player will run through the track numbers until you
let the button loose.
«-button:
If you press the «-button once, playback starts at the beginning of the previous track. If a track is already
played back, you can start the current track from the beginning.
»-button:
If you press the »-button once, the playback starts at the beginning of the next track, if you press it twice the
following track, etc.
Please note that the CD-player calls the track up in the mode you pressed the Track-button. If the CD-player
is in the Play-mode at track 1 for example and you press the »-button, the player jumps to track 2 and
immediately starts playback.
6.6 Adjusting the playback-speed
Possibility 1:
Via the Pitchfader, you can adjust the playback-speed by up to +/-100 %.
Put the CD-player into playback-mode. Press the Pitch Control-button in order to activate the Pitchfader
(LED on).
Select the speed-adjustment range by pressing the 4/8/16/100%-button.
Adjust the playback-speed via the Pitchfader (Pitch-LED of the respective speed is on).
Possibility 2:
Via the Pitch Bend-buttons you can adjust the playback-speed temporarily.
Put the CD-player into playback-mode. Press the desired Pitch Bend-button. After letting the Pitch Bend-
button loose, the player automatically returns to the original playback-speed.
Motor Off-effect:
The Motor Off-effect equals the slow stopping of the turntable, if the motor is switched off. This effect is
activated via the Pitch Bend - button. If you hold the Pitch Bend - button, the playback-speeds decreases
down to 0. If the CD has "stopped", you can re-activate playback by releasing the Pitch Bend - button.
The player jumps to the first track and is in the Pause-mode (Pause-symbol flashes).
Please note that the player automatically jumps to the section where the music starts.
Avove "track" the track number is displayed. The track remain time is displayed in M
(MIN), S (SEC) and F (FRAME).
By using the Time-button, the time-indication can be switched from track remain time
(Remain) to total remain time (Total Remain) to track playback time (Elapsed).
Above the time-indication, 10 bars are displayed showing the remaining track-time
visually. The shorter the track remain time becomes, the less bars are displayed. 15
seconds before the track-end, the bars in the display start flashing.
25/55
10602297_V_1_0.DOC
Werbung
Inhaltsverzeichnis
