Makita 4334D Betriebsanleitung Seite 10

Workpiece to be cut
Wood
Mild steel
Stainless steel
Aluminum
Plastics
CAUTION:
Adjust the speed adjusting dial only within the range
of numbers 1 through 5. Do not force the dial beyond
this range or damage to the tool may result.
Anti-splintering device (Fig. 6)
To reduce the potential for workpiece surface splin-
tering, the anti-splintering device can be used. Fit it
into the base from below so that it surrounds the sides
of the blade.
Plastic base plate (optional accessory)
(Fig. 7)
Use the plastic base plate when cutting decorative
veneers, plastics, etc. It protects sensitive or delicate
surfaces from damage. To replace the base plate,
remove the four screws.
Guide rule (rip fence; optional accessory)
(Fig. 8)
When cutting widths of under 150 mm repeatedly, use
of the guide rule will assure fast, clean, straight cuts.
To install it, loosen the bolt on the front of the base.
Slip in the guide rule and secure the bolt.
Circular guide (optional accessory) (Fig. 9)
Use of the circular guide insures clean, smooth
cutting of circles (radius: under 200 mm). Insert the
pin through the center hole and secure it with the
threaded knob. Move the base of the tool forward
fully. Then install the circular guide on the base in the
same manner as the guide rule.
Vacuum head (optional accessory)
(Fig. 10 & 11)
The vacuum head is recommended to perform clean
cutting operations. Install the plastic cover on the tool
by fitting it into the notches in the tool.
To attach the vacuum head on the tool, insert the hook
of the vacuum head into the hole in the base. The
vacuum head can be installed on either left or right
side of the base. Then connect a Makita vacuum
cleaner to the vacuum head.
10
Number
on adjusting dial
3 – 5
3 – 5
3 – 4
2 – 3
1 – 4
Installing or removing the saw blade
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing the blade.
• Always clean off the blade and blade holder before
installing the blade. Chips or foreign matter on them
may cause insufficient securing of the blade, possi-
bly resulting in blade breakage or serious injury.
Installation
1. Push the blade installing lever in the (1) direction
to release it. (Fig. 12)
2. Pull the blade installing lever in the (2) direction
until it stops with a little click. If you have difficulty
pulling it out, try to do so while moving it back and
forth in the (3) direction.
3. Rotate the blade installing lever in the (4) direction
until the clamp protrudes 5 – 7 mm from the blade
holder. (Fig. 13)
CAUTION:
If you rotate the blade installing lever excessively,
the clamp will also rotate and finally come off. In
this case, re-install it properly as lately described
in ''Installing clamp''.
4. With the blade teeth facing forward, insert the
blade into the blade holder as far as it will go.
Make sure that the back edge of the blade fits
properly into the groove of the roller. (Fig. 14)
5. With the blade held against the blade holder,
rotate the blade installing lever in the (5) direction
until it stops. (Fig. 15)
6. With the blade installing lever held in this position,
push it in the (6) direction. Then rotate the blade
installing lever to its original position. (Fig. 16)
Removal
1. Push the blade installing lever in the (1) direction
to release it. (Fig. 17)
2. Pull the blade installing lever in the (2) direction
until it stops with a little click. If you have difficulty
pulling it out, try to do so while moving it back and
forth in the (3) direction.
3. Rotate the blade installing lever in the (4) direction
and remove the blade. (Fig. 18)
4. Rotate the blade installing lever in the (5) direction
until it stops. (Fig. 19)
5. With the blade installing lever held in this position,
push it in the (6) direction. Then rotate the blade
installing lever to its original position. (Fig. 20)