Midi-Datenformat - Yamaha P-120S Bedienungsanleitung

MIDI Data Format
MIDI Data Format/MIDI-Datenformat/
Format des données MIDI/Formato de datos MIDI
If you're already very familiar with MIDI, or are using a com-
puter to control your music hardware with computer-gener-
ated MIDI messages, the data provided in this section can
help you to control the P-120/P-120S.
Falls Sie bereits mit MIDI vertraut sind oder einen Computer
zur Erzeugung von MIDI-Steuermeldungen für die Instru-
mente verwenden, können Sie sich zur Steuerung des P-120/
P-120S nach den im folgenden Abschnitt aufgeführten Spezi-
fikationen richten.
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number)
kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /
Receive: 00H ~ 7FH = C-2 ~ G8)*
vv = Velocity (Key ON = 01H ~ 7FH, Key OFF = 00H)
Data format: [8nH] -> [kk] -> [vv] (reception only)
8nH = Note OFF event (n = channel number)
kk = Note number: 00H ~ 7FH = C-2 ~ G8
vv = Velocity
* If received value exceeds the supported range for the selected
voice, the note is adjusted by the necessary number of octaves.
2. CONTROL CHANGE
Data format: [BnH] -> [cc] -> [vv]
BnH = Control change (n = channel number)
cc = Control number
vv = Data Range
(1) Bank Select
ccH Parameter
00H Bank Select MSB
20H Bank Select LSB
Bank selection processing does not occur until receipt of next Pro-
gram Change message.
(2) Main Volume (reception only)
ccH Parameter
07H Volume MSB
(3) Expression
ccH Parameter
0BH Expression MSB
(4) Damper
ccH Parameter
40H Damper MSB
(5) Sostenuto
ccH Parameter
42H Sostenuto
(6) Soft Pedal
ccH Parameter
43H Soft Pedal
(7) Effect1 Depth (Reverb Send Level)
ccH Parameter
5BH Effect1 Depth
Adjusts the reverb send level.
(8) Effect4 Depth (Variation Effect Send Level)
ccH Parameter
5EH Effect4 Depth
50
P-120/P-120S
Data Range (vvH)
00H:Normal
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H-3FH:off, 40H-7FH:on
Data Range (vvH)
00H-3FH:off, 40H-7FH:on
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Si vous êtes très familier avec l'interface MIDI ou si vous uti-
lisez un ordinateur pour commander votre matériel de musi-
que au moyen de messages MIDI générés par ordinateur, les
données suivantes vous seront utiles et vous aideront à com-
mander le P-120/P-120S.
SI usted está ya familiarizado con MIDI, o si emplea una
computadora para controlar sus aparatos musicales con
mensajes MIDI generados por computadora, los datos pro-
porcionados en esta sección le ayudarán a controlar la P-
120/P-120S.
3. MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number)
cc = Control number
vv = Data Range
(1) All Sound Off
ccH Parameter
78H All Sound Off
Switches off all sound from the channel. Does not reset Note On
and Hold On conditions established by Channel Messages.
(2) Reset All Controllers
ccH Parameter
79H Reset All Controllers
Resets controllers as follows.
Controller Value
Expression 127 (max)
Damper Pedal 0 (off)
Sostenuto 0 (off)
Soft Pedal 0 (off)
(3) Local Control (reception only)
ccH Parameter
7AH Local Control
(4) All Notes Off
ccH Parameter
7BH All Notes Off
Switches OFF all the notes that are currently ON on the specified
channel. Any notes being held by the damper or sostenuto pedal
will continue to sound until the pedal is released.
(5) Omni Off (reception only)
ccH Parameter
7CH Omni Off
Same processing as for All Notes Off.
(6) Omni On (reception only)
ccH Parameter
7DH Omni On
Same processing as for All Notes Off.
(7) Mono (reception only)
ccH Parameter
7EH Mono
Same processing as for All Sound Off.
(8) Poly (reception only)
ccH Parameter
7FH Poly
Same processing as for All Sound Off.
• When control change reception is turned OFF in the Function mode,
control change data will not be transmitted or received except for
Bank Select and Mode messages.
• Local on/off, OMNI on/off are not transmitted. (The appropriate note
off number is supplied with "All Note Off" transmission).
• When a voice bank MSB/LSB is received, the number is stored in
the internal buffer regardless of the received order, then the stored
value is used to select the appropriate voice when a program
change message is received.
• The Multi-timbre and Poly modes are always active. No change
occurs when OMNI ON, OMNI OFF, MONO, or POLY mode mes-
sages are received.
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H (off), 7FH (on)
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H