Adaptation And Setup; Installation - SCAN DSA E 1000 Montageanleitung

ENGLISH
NB: It is extremely important to ensure that the product is stable.
It must be installed on a completely inflexible floor.
It is recommended that flooring that is not attached to the
foundation – «floating floors» – be removed beneath the

installation.

3.4 Requirements for floor covering
The SCAN DSA E 1000 has an opening in the base plate (fig.
2 - pos. 1).
Note! The opening must be covered by the accompanying steel
plate (fig. 2 - pos. 12).
Any inflammable floor coverings should be removed from under
the fireplace and floor plate.
3.5 Front plate
If there is inflammable flooring in front of the insert, a plate
made of steel or some other suitably non-inflammable material
must be used.
Contact your local building authorities regarding restrictions
and installation requirements.
3.6 Requirements for air circulation
There must be a flow of air between the insert and the
surround.
This is to ensure that any build-up of heat inside the surround
is not too great. Also that there is adequate heat output into
the room.

4.0 Adaptation and setup

4.1 Painting
All surrounds are delivered unpainted!
Painting can take place the day after installation. Use latex paint.
If you want to create some surface texture, mix some tile cement
into the paint.
4.2 Cracks
In some instances, small cracks may appear at the joints after a
few months' use. These cracks can be easily repaired:
• Open up the crack with a tool, e.g. a screwdriver, to create
more room for the grouting cement.
• Remove any dust using a vacuum cleaner.
• Then inject some acrylic grout, and smooth it off using a wet,
soapy fingertip.
• After 48 hours, the joint can be repainted.
12
5.0 Assembling the
surround
The Scan DSA E 1000 consists of the following parts (fig. 2):
Part 1. Bottom plate x 1. -
Part 2. Rear section x 1. -
Part 3. Base x 1. -
Part 4. Panel, left, x 1. -
Part 5. Panel, right, x 1. -
Part 6. Cowl x 1. -
Part 7. Cowl, top, x 1. -
Part 8. Bench plate, slate, x 1. -
Part 9 Grate for outdoor air, x 1. -
Part 10 Grate for flue pipe, x 1. -
Part 11 Grate for top, x 1. -
Part 12 Floor plate, x 1. -
Install the insert in accordance with the Installation and
Operating Instructions provided with the product.
NB! We recommend test-mounting the surround before
permanently attaching the insert to the chimney so that any
necessary adjustments can be made.
Installation
1. NB! Place the bottom plate (Fig. 4A) on a steady surface
and adjust until it is standing completely level. Check that
the safety distances meet the requirements stated in the
operating instructions provided with the insert.
2. Place the accompanying steel plate over the opening in the
base plate (fig. 4B).
3. Position the back wall (Fig. 5 A). Glue with acrylic adhesive.
4. Position the insert (Fig. 6 A) on the bottom plate (Fig. 6 B).
Do not use the adjustment screws.
5. Put the base into place (Fig. 7 A). Glue with acrylic adhesive.
6. Put the panels into place (Fig. 8 A). Glue with acrylic
adhesive.
7. Put cowl 1 into place (Fig. 9 A). Make sure that the side with the
sharp edge is turned upwards. Glue with acrylic adhesive.
8. Put cowl 2 into place (Fig. 10 A). The knockout must be turned
upwards. Glue with acrylic adhesive.
9. Put the slate tile (Fig. 11 A) into place. NB: This must not be
glued down so as to allow for service access.
10. Place the cover (Fig. 12 A) over the outdoor air knockout since
a supply of external air will not be used. Glue with acrylic
adhesive.
11. Install the flue pipe (Fig. 13 A) with the damper (Fig. 13 B) in
accordance with the Installation and Operating Instructions
for Scan DSA 10 (provided with the insert).
12. Place the grates (Fig. 14 A) on the top of the surround.
cat. no. 310256
cat. no. 310257
cat. no. 310258
cat. no. 310259
cat. no. 310260
cat. no. 310261
cat. no. 310262
cat. no. 222883
cat. no. 222885
cat. no. 222886
cat. no. 222887