Additional Safety Rules For Tool - Makita 4331D Betriebsanleitung

5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
8. Be careful not to drop, shake or strike battery.
9. Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.

ADDITIONAL SAFETY RULES FOR TOOL

1. Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will make exposed metal parts of the tool
"live" and shock the operator.
3. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4. Do not cut hollow pipe.
Charging (Fig. 2)
Your new battery cartridge is not charged. You will need to charge it before use. Use the battery charger to charge the
battery cartridge.
Plug the battery charger into the proper A/C voltage source. The charging light will flash in green color. Insert the bat-
tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective
markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When
the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The
charging light will remain lit steadily during charging. When the charging light color changes from red to green, the
charging cycle is complete.
If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its
"trickle charge (maintenance charge)" mode. After charging, unplug the charger from the power source. Refer to the
table below for the charging time.
Battery type
1222 (Ni-cd)
1234 (Ni-MH)
1235 (Ni-MH)
1422 (Ni-cd)
1434 (Ni-MH)
1435 (Ni-MH)
6
5.
6.
7.
8.
9.
10. Do not leave the tool running. Operate the tool
11. Always switch off and wait for the blade to come
12. Do not touch the blade or the workpiece immedi-
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
• To remove the battery cartridge, withdraw it from the
ENB030-1
• To insert the battery cartridge, align the tongue on the
• Do not use force when inserting the battery cartridge. If
Capacity (Ah)
2.0
2.6
3.0
2.0
2.6
3.0
Do not cut oversize workpiece.
Check for the proper clearance beneath the
workpiece before cutting so that the blade will
not strike the floor, workbench, etc.
Hold the tool firmly.
Check the blade is not contacting the workpiece
before the switch is turned on.
Keep hands away from moving parts.
only when hand-held.
to a complete stop before removing the blade
from the workpiece.
ately after operation; they may be extremely hot
and could burn your skin.
the battery cartridge.
tool while pressing the buttons on both sides of the car-
tridge.
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around
you.
the cartridge does not slide in easily, it is not being
inserted correctly.
Number of cells
10
10
10
12
12
12
Charging time
Approx. 45 min.
Approx. 60 min.
Approx. 70 min.
Approx. 45 min.
Approx. 60 min.
Approx. 70 min.