Kenwood KDC-X5200BT Bedienungsanleitung Seite 22

AUDIO SETTINGS
LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5: Selects your preferred bass boost
BASS BOOST
level. ; OFF: Cancels.
LOUDNESS LEVEL1/LEVEL2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
(Not applicable if 3-way crossover is selected.)
FADER
REAR 15 to FRONT15 (0): Adjusts the rear and front speaker output balance.
BALANCE LEFT 15 to RIGHT15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET LEVEL –15 to LEVEL +6 (LEVEL 0): Preset the initial volume level of each
source. (Before adjustment, select the source you want to adjust.)
SOUND EFFECT
SOUND (Not applicable for RADIO source and AUX source.)
RECONSTRA ON: Creates realistic sound by compensating the high-frequency components
(Sound and restoring the rise-time of the waveform that are lost in audio data
reconstruction) compression. ; OFF: Cancels.
SPACE (Not applicable for RADIO source.)
ENHANCER SMALL/MEDIUM/LARGE: Virtually enhances the sound space. ; OFF: Cancels.
SOUND REALIZER LEVEL1/LEVEL2/LEVEL3: Virtually makes the sound more realistic. ;
OFF: Cancels.
STAGE EQ LOW/MIDDLE/HIGH: Virtually adjust the sound position heard from the
speakers. ; OFF: Cancels.
DRIVE EQ ON: Boosts the frequency to reduce the noise heard from outside the car or
running noise of the tyres. ; OFF: Cancels.
Depending on the crossover type you have selected ( 5), 2-way crossover
SPEAKER SIZE
or 3-way crossover setting items will be shown. ( 19)
X'OVER
By default, 2-way crossover type is selected.
DTA SETTINGS
For settings, 20, Digital Time Alignment settings.
CAR SETTINGS
• [SUB-W LEVEL] is selectable only if [SUBWOOFER SET] is set to [ON].
18
ENGLISH
Crossover settings
Below are the available setting items for 2-way crossover and
3-way crossover.
SPEAKER SIZE
Selects according to the connected speaker size for optimum
performance.
• The frequency and slope settings are automatically set for the
crossover of the selected speaker.
• When 2-way crossover is selected, if [NONE] is selected for
[TWEETER] of [FRONT], [REAR] and [SUBWOOFER] for [SPEAKER SIZE], the
[X ' OVER] setting of the speaker is not available.
• When 3-way crossover is selected, if [NONE] is selected for
[WOOFER] of [SPEAKER SIZE], the [X'OVER] setting of [WOOFER] is not
available.
X ' OVER
• [FRQ]/[FRONT-HPF FRQ]/[REAR-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/
[LPF FRQ]: Adjusts the crossover frequency for the selected
speakers (high pass filter or low pass filter).
If [THROUGH] is selected, all signals are sent to the selected
speakers.
• [FRONT-HPF SLOPE]/[REAR-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/
[LPF SLOPE]/[SLOPE]: Adjusts the crossover slope.
Selectable only if a setting other than [THROUGH] is selected for
the crossover frequency.
• [SW LPF PHASE]/[PHASE]: Selects the phase of the speaker output to
be in line with the other speaker output.
• [GAIN LEFT]/[GAIN RIGHT]/[FRONT-HPF GAIN]/[REAR-HPF GAIN]/
[SW LPF GAIN]/[GAIN]: Adjusts the output volume of the selected
speaker.