Care And Service - Kärcher SC 5 EasyFix Bedienungsanleitung

and speeds up the ironing process. In any case, the
ironing board used should have a steam-permeable,
grid-like ironing base surface.
Note
Do not turn on the steam stage for the VapoHydro func-
tion when the steam pressure iron is plugged in, since
otherwise the ironing laundry will get wet.
Recommended steam stages
Stage
Min. steam stage
Max. steam stage
1. Ensure that tap water or a mixture of tap water and
no more than 50% distilled water is in the steam boil-
er of the steam cleaner.
2. Insert the steam plug of the iron into the unit plug un-
til it clicks into place.
3. Putting the steam cleaner into operation; see Chap-
ter Switching on the device.
4. Wait until the steam cleaner is ready for use.
Steam ironing
All fabrics can be ironed with steam. Iron sensitive fab-
rics or overprints on the reverse or, as the case may be,
according to manufacturer's instructions.
ATTENTION
Damage to garments
Failure to observe the ironing information in the garment
may result in damage.
Observe the ironing information in the garment.
Note
For sensitive textiles, we recommend using the
KÄRCHER non-stick electric iron plate BE 6006.
Note
The iron plate must be hot to prevent steam from con-
densing on the sole plate and dripping onto the ironing
laundry.
The iron can be held vertically for steaming curtains,
dresses, etc.
1. Set the temperature controller of the iron within the
selected range (
As soon as the orange heating indicator light of the
iron goes out, ironing can be started.
2. Press the "steam" switch (top) or the "steam" switch
(bottom).
 Steaming at intervals: Press the "steam" switch.
Steam flows out as long as the switch is pressed.
 Continuous steaming: Pull the lock for the
"steam" switch backwards until it engages. Steam
flows out continuously. To release, push the lock
forward.
3. Before ironing and after pauses in the ironing pro-
cess, direct the blast of steam onto a cloth until the
steam flows evenly.
Dry ironing
ATTENTION
Damage to the device
Water shortage in the steam boiler leads to damage to
the device
Make sure that there is water in the steam boiler.
ATTENTION
Damage to garments
Failure to observe the ironing information in the garment
may result in damage.
Observe the ironing information in the garment.
16
Clothing fabrics
Garments with few wrin-
kles
Jeans
/MAX).
1. Set the temperature controller of the iron in accord-
ance with the garment.
Synthetics
Wool, silk
Cotton, linen
2. Wait until the iron's heating indicator light goes out.
The iron is ready for ironing.

Care and service

Descaling the steam boiler
Note
Since the lime clogs the appliance, we recommend des-
caling the appliance based on the number of times the
water reservoir is filled as specified in the table (TF=tank
fillings).
Hardness range
I soft
II Medium
III Hard
IV Very hard
Note
Your water board or municipal utilities authority can pro-
vide information on hardness of tap water.
ATTENTION
Damaged surfaces
The descaler may corrode sensitive surfaces.
Fill and empty the appliance carefully.
1. Switch off the appliance, see Chapter Switching off
the device.
2. Allow the appliance to cool down.
3. Drain the water reservoir.
4. Remove the accessory/accessories from the acces-
sory holders.
5. Open the cap of the accessory compartment.
6. Remove the accessory from the accessory compart-
ment.
7. Open the maintenance lock. To do this place the
open end of an extension tube on the maintenance
lock, insert this into the guide so it engages and
open it.
Illustration S
8. Drain the water completely out of the steam boiler.
Illustration T
ATTENTION
Appliance damage due to descaler
An unsuitable descaler or incorrect dosing of the descal-
er may damage the appliance.
Only use KÄRCHER descaler.
Use 1 dosing unit of the descaler for 0.5 l water.
9. Apply descaler solution to the descaler according to
the details.
10. Fill the descaler solution into the steam boiler. Do
not seal the steam boiler.
11. Allow the descaler solution to take effect for
approx. 8 hours.
12. Drain descaler solution completely out of the steam
boiler.
13. Repeat the descaling process if necessary.
14. Rinse the steam boiler 2-3 times with cold water in
order to drain all the descaler solution residue.
15. Drain the water completely out of the steam boiler.
16. Dry the mounting for the grid connection cable.
English
°dH mmol/l
0-7 0-1.3
7-14 1.3-2.5
14-21 2.5-3.8
>21 >3.8
TF
100
90
75
50