Maintenance; Environmental Protection / Disposal; 11 Warranty; 12 Declaration Of Conformity - Protool AGP 125-11 D Originalbetriebsanleitung Und Ersatzteilliste

9

Maintenance

- The unit should be stored in a dry place where
it is protected against freezing.
- Ventilation apertures [1-2] must not jam.
- Cable replacement can be carried out only in a
specialised electrical technical workshop, au-
thorized for such work. Only original PROTOOL
cable can be used for spare parts.
After approximately 200 hours of operation, the
following work must be carried out:
- Brush length inspection. If brush is shorter than
5 mm, replace it. Only original PROTOOL brush
can be used as spare part.
- Device will switch off automatically; if the brush-
es are worn down the device must be sent to a
specialized centre for maintenance.
WARNING
To maintain the protection level, the device
must be checked in a specialized electrical
technical workshop, which is authorized for
such work and will inspect the safety of the
device.
- Service – see enclosed sheet.
10 Environmental
Protection / Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into house-
hold waste!
According to the European Directive 2002/96/EC
on waste electrical and electronic equipment and
its incorporation into national law, power tools that
are no longer suitable for use must be separately
collected and sent for recovery in an environmen-
tal-friendly manner.
REACh
REACh is a European Chemical Directive that
came into effect in 2007. As "downstream users"
and product manufacturers, we are aware of our
duty to provide our customers with information.
We have set up the following website to keep you
updated with all the latest news and provide you
with information on all the materials used in our
existing products:
http://www.tts-protool.com/reach
18

11 Warranty

For our tools, we give warranty for material and
production defects in accordance with the locally
applicable legal provisions, but in any case for at
least 12 months. Within the EU member states, the
warranty period is 24 months (verifi cation through
invoice or delivery note).
Damage caused by, in particular, natural wear,
overloading, incorrect handling, or damage caused
by the operator, or damage caused through use of
the equipment contrary that specifi ed in the Oper-
ating Instructions, or damage which was known at
the time of purchase, is not covered by the war-
ranty. Furthermore, damage caused by the use of
non-original PROTOOL accessories and consumable
material (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is
returned while still assembled to the supplier or an
authorised PROTOOL Customer Service workshop.
Keep the Operating Instructions, Safety Instruc-
tions, Spare Parts List and purchase receipt in a
safe place. Otherwise the respective, current war-
ranty conditions of the manufacturer shall apply.
Note
Due to continuous research and development work,
we reserve the right to make changes to the tech-
nical content of this documentation.

12 Declaration of Conformity

Angular grinder
AGP 125-11 D
AGP 125-12 D
AGP 125-14 D
AGP 125-14 DE
We declare under our sole responsibility that this
product is in conformity with the following stand-
ards or standardization documents:
EN 55 014-1, EN 55 014-2, EN 60 745-1,
EN 60 745-2-3, EN 61 000-3-2, EN 61 000-3-3
according to the provision of the regulations stipu-
lated in Directive 2006/42/EC, 2004/108/EC.
All the procedures were applied as validly amended
at the time of the issue of this declaration, without
quoting these.
Technical documentation is kept at the manufac-
turer.
11
Stanislav Jakeš
Research and development
Protool GmbH
Wertstr. 20
D-73240 Wendlingen
30. 9. 2011
Serial no.
636677
639077
763884
765077