Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
b. As a stationary machine on the subframe. In
this case the machine must be secured to the
subframe with 4 bolts and the subframe
anchored to the floor or to a floor plate with
dimensions of at least 1 square metre
Assembly of the bench saw on the workbench
Fig. B & C
Before adjusting the saw, make sure the
plug is removed from the socket.
Fig. B shows the distance of the holes to be drilled
in the workbench on which to fasten the machine.
Drill holes of 8 mm.
Only use the machine after it has been
assembled completely and it has been
screwed onto the workbench or the
frame.
•
Fig. C shows the part to be sawn out (310 x
310 mm), so that the sawdust can fall through
it and piling up is prevented! Only if you do not
use an extraction system!
•
Fasten the machine with bolts.
•
If the frame is used, it must be fixed on the
floor with four screws and the machine must
be fixed on the frame with four screws. Check
the screws before switching the machine on.
Assemble undercarriage
Fig. G
•
Turn the machine upside down.
•
Remove the black plastic bottom plate by
unscrewing the 6 screws. (Fig. G-1).
•
Unscrew the adjusting knob on the front and
tilt the motor (Fig. G-2), then remove the
transport packing (Fig. G-3).
•
Now place one by one the uprights in the
casing of the sawing bench (Fig. G-4).
•
Secure the uprights with 4 screws using a
screwdriver, do not completely tighten the
screws (Fig. G-5).
•
Fit the 4 support bars, do not completely
tighten the screws (Fig. G-6)
•
Fit the black plastic bottom plate and screw it
tight.
•
Attach the rubber feet under the uprights (Fig.
G-7).
•
Turn the machine into an upright position on a
flat surface and adjust the machine so that it
stands in a stable position, tighten all the nuts
and bolts (Fig. G-7).
Assemble bracket/push stick
•
Attach the 2 brackets onto the casing of the
sawing bench and screw them tight (Fig. G-8).
•
Place the push stick in the brackets.
Assembly and attachment of the rip fence
Fig. D
•
Attach the aluminium fence (A) to the
positioning block (B).
•
Now you can attach the complete rip fence to
the bench top.
•
Slide the rip fence via one end of the
positioning rail (C) over the bench top.
•
Adjust the position of the aluminium fence
profile (A) such that the end corresponds to
the rear edge of the saw.
Assembly of the riving knife and the
protective cap
Fig. E
•
Turn the saw blade completely upwards.
•
Remove the bench inlay.
•
Assemble the riving knife on the set-up for this
purpose and use hereby the Allen screws and
the filling rings. Ensure that the riving knife
falls properly into the opening (= groove).
•
Now put the inlay back in the bench and
fasten it.
•
Now assembly the protective cap onto the
riving knife and use hereby the profiled nut
and self-locking nut.
Now lay a lath against the saw blade and
the riving knife and check whether it falls
properly into the extension of the saw
blade. If this is not the case: Loosen the
fastening bolts and place or remove the
filling rings.
•
Above the saw table the radial distance
between the riving knife and the toothed rim of
the saw blade shall not at any point exceed 5
mm at the depth of cut set.
•
The tip of the riving knife shall not be lower
than 5 mm from the tooth peak, as shown.
EN
9
Werbung
Inhaltsverzeichnis
