STUDER REVOX PR99 Bedienungsanleitung Seite 33

FUNCTIONS OF THE OPERATING CONTROLS
TAPE DECK
Left-hand reel support
[1]
Mount full
reel on
this
side.
Right-hand reel support
[2]
Mount empty
reel on
this
side.
Tape
counter
[3]
Tape
counter reset key
[4]
Tape
guide pin,
left-hand
[5]
Tape
guide pin,
right-hand
[6]
Cutter slide
[7]
Fast
forward >
[14]
When
operating this slide,
the tape
will
be
pressed
against
the
This key causes
immediate
fast
forward winding
of the
tape. lt
is
sound heads. Thus.
the cutting position can
be
searched
by
used
in
the same manner
as
key
[13]
manually turning the reels This
function can
be cancelled
by
depressing the
PLAY
key
[15]
or by lightly
pushing
the
pressure
PLAY
key
[15]
roller against the
capstan.
The reproduce function
is
initiated
by depressing the PLAY key.
lt
may also be
depressed while fast forward
or
rewind
is active.
Speed
selectors
SPEED
[B]
Select desired tape speed
by
depresslng the corresponding
but-
STOP
key
[16]
ton(self-locking).Thetapespeedmaybechangedinanyoper-
Thiskeycancelsthecurrentmodeof operation.Thetapedeckis
ating
mode.
ready to accept
a
new command.
Mains
switch
POWER
[9]
REC
key
[17]
Before
switching
on
the
tape
deck, check setting
of
voltage
tap-
This
key
is
only
active
if
the
PLAY
key [15]
is
depressed simulta-
ping
switch
atthe rearof thetape
deck.
neously.Therecordingfunctioncanbeentereddirectlyfromthe
The tape deck switched on by setting the
POWER
switch
[9]
to
fast forward or rewind
mode.
To
prevent unintentional
erasure,
the ON position.
When power
is
applied, the VU-meters [23]
are
the individual channels can
be
protected
by setting
switch
[25]
illuminated.
to the
SAFE
position.
"Soft drop-in"
is
only possible
by
simultaneously depressing the
REEL SIZE
buttons [10]
REC
[17]
and
PLAY
l15l
keys
When
using small-diameter tape
reels (1Bcm
or
smaller). the
REEL SIZE
button
[10]
should
be
depressed.
lf
the
hub
diameter
is
larger than 60 mm, this button
does not need to
be
depressed.
TAPE
DUMP
button
[11]
The right-hand spooling motor
remains
disabled
as long
as
this
button
is
depressed.
ln
this mode, obsolete tape sections can
be
played
rnto
the "waste basket"
by
depressing
the
PLAY
key
[15]
PAUSE
key
l12l
ln contrast to the
STOP
key
[16].
the currently active operating
modes can
be
suspended
at any
time
by depressing the
pause
key.
As
soon as
the
pause key [12]
is released, the
tape deck
re-
enters
the previously established operating mode.
For longer
pauses,
the self-locking key of the remote control can be used.
Fast
rewind
(
['13]
Depressing this key
results
in
immediate rewinding
of the tape.
This
function can
be
selected directly from
any other operating
mode. The
rewind function
term inates
if
the
STO P
key
[16]
is
de-
pressed,
a
new command
is
entered, oi when the optical tape
end sensor detects the end of the
tape.
With
slider
[7]
in
the
cutter position, the rewind function
remains
active only as long
as
this key stays depressed,
thus
allowing
motorized search of
a
cutting
position.
Note:
To
reduce
wear
on the soundheads, long tape sections should
not
be
wound
in
the cutter position.