Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications - Makita JN3201 Betriebsanleitung

Vorschau ausblenden Andere Handbücher für JN3201:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
ENGLISH
(Original instructions)
1
Stainless steel gauge: 2.5 mm
(3/32")
2
Mild steel gauge: 3.2 mm (1/8")
3
Switch trigger
4
Lock button
5
Wrench
6
Lock nut
7
Die holder
8
Punch

SPECIFICATIONS

Max. cutting capacities
Min. cutting radius
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting sheet steel and stainless
sheet steel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
4
Explanation of general view
9
Screw
10 Cutting edge
11 Groove
12 Punch holder
13 Pin
14 Hex wrench
15 Washer
16 Insert washer in between
17 Die
Model
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Strokes per minute (min
Overall length
Net weight
Safety class
ENE037-1
ENF002-2
GEA010-1
2
2
2
2
Outside edge
Inside edge
–1
)
NIBBLER SAFETY WARNINGS
1.
Hold the tool firmly.
2.
Secure the workpiece firmly.
3.
Keep hands away from moving parts.
4.
Edges and chips of the workpiece are sharp.
Wear gloves. It is also recommended that you
put on thickly bottomed shoes to prevent injury.
5.
Do not put the tool on the chips of the work-
piece. Otherwise it can cause damage and trou-
ble on the tool.
6.
Do not leave the tool running. Operate the tool
only when hand-held.
7.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
8.
Do not touch the punch, die or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
9.
Avoid cutting electrical wires. It can cause seri-
ous accident by electric shock.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
18 Grind/sharpen; 0.3 – 0.4 mm
(1/64")
19 Remove dull portion
20 3.5 – 4.0 mm (1/8" – 5/32")
21 Limit mark
22 Screwdriver
23 Brush holder cap
JN3201
3.2 mm / 10 ga
2.5 mm / 13 ga
1.0 mm / 20 ga
3.5 mm / 10 ga
128 mm
120 mm
1,300
225 mm
3.4 kg
/II
GEB028-2

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis