Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch Performance Line Nyon BUI275: 1 270 020 915 Originalbetriebsanleitung

OBJ_BUCH-2616-003.book Page 11 Wednesday, June 14, 2017 2:24 PM
Code Cause
610 Battery pack voltage error
620 Charging error
640 Internal battery pack error
655 Multiple battery pack errors
656 Software version error
7xx Transmission error
No display Internal error of the on-board com-
puter
Power Supply of External Devices via
USB Connection
With the USB connection, it is possible to operate and charge
most devices whose power supply is possible via USB (e.g.,
various mobile phones).
Prerequisite for charging is that the on-board computer and a
sufficiently charged battery pack are inserted in the eBike.
Open the protective cap 9 of the USB port on the on-board
computer. Connect the USB connection of the external device
to the USB port 8 on the on-board computer using the USB
charging cable Micro A – Micro B (available from your Bosch
eBike dealer).
Once the consumer has been disconnected, the USB connec-
tion must be sealed again carefully with the protective cap 9.
 USB connections are not a waterproof. When cycling in
the rain, do not connect any external devices and make
sure that the USB port is fully covered by the protective
cap 9.
Attention: Users connected to Nyon can affect the range of
the eBike.
Notes on Riding with the eBike System
Careful Handling of the eBike
Please observe the operating and storage temperatures of the
eBike components. Protect the drive unit, on-board computer
and battery against extreme temperatures (e.g. from intense
sunlight without adequate ventilation). The components (es-
pecially the battery pack) can become damaged through ex-
treme temperatures.
Keep the screen of your Nyon clean. Dirt can cause faulty
brightness detection. The day/night switch-over in the navi-
gation mode can be distorted.
An abrupt change of environmental conditions, can cause the
screen to fog up from inside. After a short time, a temperature
adjustment takes place and the fog disappears.
Bosch eBike Systems
Corrective Measure
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Replace the charger. Contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Switch off the eBike system. Remove the battery pack and reinsert it.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Contact your Bosch eBike dealer so that he can perform a software
update.
Please observe the operating instructions provided by the transmission
manufacturer.
Restart your eBike system by switching it off and back on.

Maintenance and Service

Maintenance and Cleaning

Do not immerse any components, including the drive unit, in
water or clean them with pressurised water.
Clean your on-board computer using a soft cloth dampened
only with water. Do not use any detergents.
Have your eBike system checked by an expert at least once a
year (including mechanical parts, up-to-dateness of system
software).
The bicycle manufacturer or dealer may also base the service
date on the distance travelled and/or a period of time. In this
case, the on-board computer displays a message telling you
when the service date is due for four seconds after each time
it is switched on.
For service or repairs on the eBike, please refer to an author-
ised bicycle dealer.
 Have all repairs performed only by an authorised bike
dealer.

After-sales Service and Application Service

In case of questions concerning the eBike system and its com-
ponents, please refer to an authorised Bosch eBike dealer.
For contact data of authorised Bosch eBike dealers, please
refer to www.bosch-ebike.com
Transport
 If you transport your eBike attached to the outside of
your car, e.g. on a bike rack, remove the on-board com-
puter and the PowerPack to avoid damaging them.
English–11
1 270 020 XBN | (14.6.17)