La Cornue CornuFé 90 Bedienungsanleitung Seite 35

Re-assemble in reverse order.
13. To Remove the Door Latch
Remove the oven outer door panel as detailed in Section
12. Remove the fixings that secure the latch assembly to the
inner door panel. Fit the replacement catch and re-assemble
in reverse order. Check correct operation of door.
14. To Remove the Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from the
door centre until that hook is released.
Proceed to the next hook and release it in a similar way, and
so on. Use force if the hooks are stiff, as the old seal will be
discarded.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door, and
proceed round the door snapping in each hook in turn.
15. To Adjust the Oven Door Catch Keeper
Open the oven door and slacken the locknut at the keeper
base. Adjust the keeper inward or outward as required, until
the desired door operation is obtained.
Re-tighten the locknut.
16. To Remove the Hotplate Spark Generator
Disconnect the appliance from the electricity supply.
Pull the unit forward to access the cover boxes at the
appliance rear. Remove the fixings that secure the cover
and lift it clear. Undo the terminal connections noting their
positions.
Undo the fixings that secure the spark generator and remove
the device.
17. To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
Remove the pan supports, hotplate accessories and burner
heads. Remove the hotplate as detailed in Section 1. Remove
the cover box and disconnect all HT leads at the generator.
Remove the lower back panel and disconnect the lead at the
electrode. Pull the sleeved bundle of HT leads up through
the rear upright. Pull the appropriate lead from the sleeve
and push in the replacement. Replace the leads in the rear
upright. Re-connect the leads at the generator and oven
electrode. Re-assemble in reverse order and check ignition.
18. To Remove Oven Inner Back
Open the oven door. For the left-hand oven unscrew the 2
thermostat phial fixing screws.
Remove the fixings that secure the inner back to the oven
rear. Lift the removable panel away.
Re-assemble in reverse order. Ensure that the retaining fixings
are fully tightened.
19. To Replace an Oven Fan
Disconnect the appliance from the electricity supply.
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fixings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in Section 18.
Hold the fan blades and undo the centre nut (LH thread),
brass washers, fan blade and circlip.
Undo the fixings that retain the fan and remove it from the
cavity rear. Fit the replacement and re-assemble parts in
reverse order. Check that the oven operates satisfactorily.
20. To Remove an Oven Fan Element
Disconnect the appliance from the electricity supply.
Pull the unit forward to access the cover boxes at the rear
of the appliance. Remove the fixings that secure the cover
and lift it clear. Undo the terminal connections noting their
positions. Remove the inner back as detailed in Section 18.
Remove the fixings that secure the element within the oven
and lift the element away carefully.
Fit the replacement element and re-assemble parts in reverse
order.
Check that the oven operates correctly.
21. To Remove the left-hand Oven Bottom and Top
Elements
Disconnect the appliance from the electricity supply.
Bottom Element
Pull the cooker forward to access the cover boxes at the rear
of the unit. Remove the fixings that secure the cover and lift
it clear.
Remove the 2 screws and allow the plate to drop down.
Remove the 2 screws, lower the upper plate and remove
through the slot in the cooker back.
Undo the terminal connections, noting their positions.
Remove the element fixings and withdraw element. Replace
the element and re-assemble parts in reverse order.
Top Element
Open the left-hand oven door and undo the fixings that
secure the heat shield. Remove the top element bracket
fixings and withdraw element. Replace the element and re-
assemble parts in reverse order. Check that the oven operates
satisfactorily.
22. To Adjust the Oven Door Angle
The door bottom hinge can be adjusted to alter the angle of
the door.
Loosen the bottom hinge fixing screws and use the notch and
a flat bladed screwdriver to move the position of the hinge to
set the hinge position.
Retighten the hinge screws.
34
English