La Cornue CornuFé 90 Bedienungsanleitung Seite 34

English
Replace all parts in reverse order.
When replacing any electrical connections refer to the wiring
diagram.
3. To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply. Remove
the control panel – see 2. Remove the retaining screw on the
upper front edge and the two fixings on the rear or the side
panel. Undo the lower retaining screw situated below the
edge at the panel front corner. Remove the panel by pulling it
away from the appliance.
4. To Remove an Oven Neon
Disconnect the appliance from the electricity supply.
Remove the control panel – see 2. Remove the relevant neon
connection and undo the nut which secures the neon to
the control panel. Replace parts in reverse order. Ensure the
replacement neon functions correctly.
5. To Remove a Thermostat
Disconnect the appliance from the electricity supply. Remove
the hotplate – see 1. Remove the control panel – see 2 Open
the appropriate oven door and remove the oven shelves. Pull
the appliance forward to gain access to the rear cover box.
Undo the cover screws and lift clear.
Right–hand Oven
Remove the two fixings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the oven
back panel.
Left–hand Oven
Remove the two screws holding the thermostat phial to the
oven fan cover at the rear of the oven. Pull the unit forward
to access the rear of the cooker. Remove the cover boxes
by removing the fixing screws and lifting clear. Feed the
thermostat capillary clear of the oven.
Disconnect the wires from the thermostat and undo the two
fixings which secure the control to the mounting plate.
Fit the replacement and re-assemble in reverse order. Ensure
that the phial is clipped to the oven rear, positioned centrally
between the clips. Check that the thermostat functions
correctly.
6. To Remove an Oven element Thermal Cut-out
Pull the cooker forward to gain access to the cover box. Undo
the cover screws and lift clear. The cutout is located on the
earth plate beside the oven element connections. Disconnect
the cutout wiring. Undo the fixings that secure the cutout to
the earth plate and remove. Fit replacement control and re-
assemble in reverse order.
7. To Remove a Hotplate Tap
Remove the hotplate and control panel, see 1 and 2.
Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove the fixings
that secure the tap to the gas rail. Disconnect the ignition
switch wiring.
Remove the tap. Remove and discard the gasket seal. Fit new
gasket seal to replacement tap.
Re-assemble in reverse order. Check the appliance is gas
sound. Check hotplate ignition.
8. To Change an Ignition Switch
Change the gas tap as detailed in Section 7.
9. To Remove a Hotplate Burner Injector
Disconnect the appliance from the electricity supply.
Remove pan support and burner head. Undo the large brass
nut and remove the brass venturi. Lift up the burner base and
disconnect the ignition lead from the electrode. The injector
is now accessible using a long box spanner.
Alternatively, remove the hotplate as detailed in Section 1.
Remove the injector directly from the burner body. Fit the
appropriate injector.
Re-assemble in reverse order. Check the appliance is gas
sound.
10. To Remove a Hotplate Burner Spark Electrode
Disconnect the appliance from the electricity supply. Remove
the pan supports, hotplate accessories and burner heads.
Undo the bezel venturi and remove the bezel from the
hotplate. The spark ignition wire will be pulled through the
electrode clearance hole. Disconnect the spark electrode
from the ignition wire.
:
Note
Take care to prevent the ignition wire from falling back
through the clearance hole. Undo the spark electrode from
the bezel by removing the spring clip and spring. Fit the
replacement electrode to the burner bezel. Ensure that the
spring and clip are properly located. Replace in reverse order
and check correct burner ignition.
11. To Remove a Hotplate Burner
Remove the pan supports, hotplate accessories and burner
heads. Remove the hotplate as detailed in Section 1.
Remove the nut that secures the burner body to the support
channel. Remove the fixings that secure the support channel
to the chassis. Lift the channel clear of the appliance.
Undo the compression fitting which connects the burner
body to the gas pipe. Remove the burner body from the
appliance.
Replace in reverse order. Check the appliance is gas sound
and that the burner operates satisfactorily.
12. To Remove the Oven Outer Door Panel
Open the oven door. Remove two screws 'A' and two screws
'B' from the door. Remove the outer door panel. Fit the
replacement panel to the oven inner door.
33