Attachment And Operation - Scheppach Hm81L Originalbetriebsanleitung

8. Attachment and operation

8.1 Attaching the mitre saw
(fig.1/2/4/5)
• In order to adjust the rotary table (13), loosen the
set screw (10) approximately 2 turns .
• Turn the rotary table (13) and pointer (11) to the de-
sired angle measurement on the scale (12) and use
the set screw (10) to secure it.
• Pressing the machine head (4) lightly downwards
and removing the locking bolt (21) from the motor
bracket at the same time disengages the saw from
the lowest position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to
the left or right on the fixed saw table (14). Insert the
clamping devices (7) in the holes on the rear side
of the stop rail (15) and secure it with the star grip
screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must
only be mounted on the right side (see fig. 11-12).
• It is possible to tilt the machine head (4) a max. 45°
to the left by loosening the set screw (20).
8.2 Precision adjustment of the stop for crosscut
90° (fig. 1/2/5/6)
• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (21).
• Loosen the set screw (20).
• Position the angle stop (A) between the saw blade
(6) and the rotary table (13).
• Loosen the lock nut (24a).
• Adjust the adjusting screw (24) until the angle be-
tween the saw blade (6) and rotary table (13) is 90°.
• Re-tighten the lock nut (24a).
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 0° on the angle
scale (18) and re-tighten the retaining screw.
8.3 Crosscut 90° and turntable 0° (fig. 1/2/7)
Attention! For 90° crosscuts, the moveable stop rail
(16a) must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop
rail (16a) and push the moveable stop rail (16a) in-
wards.
• The moveable stop rail (16a) must be locked in a
position far enough from the inner position that the
distance between the stop rail (16a) and the saw
blade (6) is no more than 8 mm.
• Before making the cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Use the handle (1) to push back the machine head
(4) and fix it in this position if required (dependent on
the cutting width).
• Place the piece of wood to be cut at the stop rail
(15) and on the turntable (13).
• Lock the material with the clamping devices (7) on
28 GB/IE
the fixed saw table (14) to prevent the material from
moving during the cutting operation.
• Release the lock switch (3) and press the ON/OFF
switch (2) to start the motor.
• When the cutting operation is completed, move the
machine head back to its upper (home) position and
release the ON/OFF button (2).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not
release the handle (1) after completing the cut; in-
stead allow the machine head to move upwards
slowly whilst applying light counter pressure.
8.4 Crosscut 90° and turntable 0° - 45° (fig. 1/7/8)
The mitre saw can be used to make crosscuts of 0°
-45° to the left and 0° -45° to the right in relation to
the stop rail.
Important! For 90° crosscuts, the moveable stop rail
(16a) must be fixed in the inner position.
• Open the set screw (16b) for the moveable stop
rail (16a) and push the moveable stop rail (16a) in-
wards.
• The moveable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a minimum of 8 mm.
• Before making the cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Lossen the set screw (10).
• Use the handle (1) to adjust the rotary table to the
desired angle.
• The pointer (11) on the rotary table must match the
desired angle on the scale (12) on the fixed saw
table (14.
• Re-tighten the set screw (10) to secure the rotary
table (13).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/5/9/10)
• No stop angle included.
• Lower the machine head (4) and secure it using the
locking bolt (21).
• Fix the rotary table (13) in the 0° position.
Attention! For mitre cuts (inclined saw head), the of
the moveable stop rails (16a) must be fixed in the
outer position.
• Open the set screw (16b) for the moveable stop rail
(16a) and push the moveable stop rail (16a) out-
wards.
• The moveable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Loosen the set screw (20) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (B) between the saw blade
(6) and rotary table (13).