Unpacking; Before Commissioning; Assembly And Operation; Mains Power Connection - Scheppach Hc85V Originalbetriebsanleitung

Noise data
The noise levels have been determined in accordance
with EN ISO 3744:1995.
Sound power level L
WA
Sound pressure level L
pA
Uncertainty K
wa/pA
Wear hearing protection.
- The total vibration emission values specified and the
device emissions values specified have been meas-
ured in accordance with a standardised test proce-
dure and can be used for comparison of one electric
tool with another.
- The total vibration emission values specified and the
device emissions values specified can also be used
for an initial estimation of the load.
A warning:
- The vibration values and noise emission values can
vary from the specified values during the actual use
of the electric tool, depending on the type and the
manner in which the electric tool is used, and in par-
ticular the type of workpiece being processed.
- It is necessary to determine the safety measures for
the protection of the operator based on an assess-
ment of the vibration load during the actual conditions
of use (In doing so, all parts of the operating cycle
must be taken into account such as times in which
the electric tool is switched off or times in which it is
switched on, but is not running under a load).
7.

Unpacking

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the device by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your device.
97 dB
82 dB
0.3 / 3 dB
www.scheppach.com
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Before commissioning

• Before connecting, make certain that the data on the
type plate matches with the mains power data.
• Check the device for transport damage. Report
any damage immediately to the transport company
which was used to deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Long air lines and supply cables (extension cable)
should be avoided.
• Ensure that the intake air is dry and dust-free.
• Do not install the compressor in a damp or wet room.
• Operate the compressor only in suitable areas (well
ventilated, ambient temperature +5°C to 40°C).
There must be no dust, acids, vapours, explosive
gases or inflammable gases in the room.
• The compressor is designed to be used in dry
rooms. It must not be used in areas where splashed
water is present.
• The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
9.

Assembly and operation

m Attention!
Always make sure the device is fully assembled
before commissioning!
9.1 Fitting the wheels (fig. 3)
• Fit the wheels (4) provided as shown.
9.2 Mounting the foot (Fig. 3)
• Fit the foot (5) provided as shown in.
9.3

Mains power connection

• The compressor is equipped with a mains cable
with an earthed plug. This can be connected to any
mains socket 230 V ~ / 50 Hz with an earth contact
and that is protected at 16 A.
• Before commissioning, ensure that the mains volt-
age matches with the operating voltage and the ma-
chine's power rating on the type plate.
GB | 23