Electrical Connection; Cleaning And Maintenance - Scheppach Vc30 Premium Originalbetriebsanleitung

11 Electrical connection

The connection complies with the applicable national
provisions.
Connections and repair work on the electrical equipment
may only be carried out by electricians.
• Before commissioning, ensure that the mains voltage
matches with the operating voltage on the type plate.
• Pay attention to the manufacturer's instructions when
using extension cables.
11.1 Damaged electrical connection
cables
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are passed
through windows or doors,
• Kinks where the connection cable has been improper-
ly fastened or routed,
• Places where the connection cables have been cut
due to being driven over,
• Insulation damage due to being ripped out of the wall
socket,
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation dam-
age.
Check the electrical connection cables for damage regu-
larly. Ensure that the connection cables are disconnected
from electrical power when checking for damage.
Electrical connection cables must comply with national
provisions. Only use connection cables of the same des-
ignation.
The printing of the type designation on the connection ca-
ble is mandatory.
Safety information for replacing damaged or defective
mains connection cables
Connection type Y
If it is necessary to replace the mains connection cable,
this must be done by the manufacturer or their represen-
tative to avoid safety hazards.
11.2 Important information
In the event of overloading, the motor will switch itself off.
After a cool-down period (time varies) the motor can be
switched back on again.

12 Cleaning and maintenance

WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
24 | GB
WARNING
Improper maintenance or cleaning work can
cause injuries!
WARNING
The product may start unexpectedly and cause inju-
ries and burns during cleaning, repair and mainte-
nance work.
– Switch the product off.
– Pull out the mains plug.
– Allow the product to cool.
12.1 Cleaning
1. Never immerse the product in water or other liquids
for cleaning.
2. Do not splash the product with water.
3. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
4. Ventilation openings must always be free.
5. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
12.1.1
WARNING
Empty and clean the product before and after
use to avoid the accumulation of materials
that could pose a fire risk in the product.
1. Remove the container cover (2) from the container (3)
as described in 8.1.
2. Empty the container (3).
12.1.2
1. When wet dirt is present, open the drain cap (6) to al-
low the liquid sucked up to drain.
2. Lift the product by the handle (1) and tilt it slightly to
pour liquid residues out of the container (3).
3. Put the drain cover (6) back on the drain hole. Close it
by turning the drain cover (6) clockwise.
4. To ensure that the container (3) is empty, proceed as
described in 12.1.1.
12.1.3
Clean the foam filter (22) or the filter cartridge (23) if the
suction power decreases.
Note:
Before installing the filter again, make sure that it is dry.
1. Remove all nozzles (16/17/19/20) and the telescopic
pipe (14) from the holder (2a/4b).
2. Take off the container cover (2) as described in 8.1.
3. Flip the container cover (2).
www.scheppach.com
Emptying the container (3) (Fig. 1)
Empty the container (3) after wet
vacuuming (Fig. 1, 14)
Cleaning the foam filter (22) and filter
cartridge (23) (Fig. 1, 7, 8)