Scheppach CUC20-BE Originalbetriebsanleitung Seite 25

3. Insert the two nipples into the recesses. In the end
position, turn the suction hose (22) in a clockwise
direction.
Blowing (Fig. 11)
1. Connect the suction hose (22) to the blast function
connection port (14a).
2. Slide the end of the suction hose connection (23)
with the two nipples into the connection with blow-
er function (14a).
3. Insert the two nipples into the recesses. In the end
position, turn the suction hose (22) in a clockwise
direction.
Fitting plastic extension tubes (25), suction hose
(22) and nozzles (26, 27, 28, 29, 36) (Fig. 10, 13)
1. Connect the plastic extension tubes (25) together.
2. Connect the assembled plastic extension tubes
with the bent end of the suction pipe (21).
3. Fit one of the corresponding nozzles (26, 27, 28,
29, 36) to the end of the plastic tube (25) or the
curved end of the suction pipe (21).
Fitting the water channels (16, 24, 25) (fig. 12, 13)
1. To do this, push the end of the respective water
channel (16, 24) with the two nipples into the water
channel connection (4, 7).
2. Insert the two nipples into the recesses. In the end
position, turn the water channel (16, 24) in a clock-
wise direction. (Fig. 12, 13).
3. Slide the end of the water channel from the end of
the extension tube (25) or the curved end of the suc-
tion pipe (21) with the two nipples into the recesses
at one of the corresponding nozzles (26, 27, 28, 29).
4. In the end position, turn the water channel in a
clockwise direction. (Fig. 13).
10. Start-up
Warning! Switch the product off if liquid or foam
emerges with the exhaust air during wet vacuuming.
Attention!
Always make sure the product is fully assembled
before commissioning!
Switching on/off (Fig. 11)
1. Insert the product's mains plug.
2. Press the on/off switch (5):
• Switch setting 0: Off
• Switch setting I: On
• Switch setting II: On + spray function
Switching on the washing function (Fig. 19)
1. Switch on the product with the spray function (see
Switching on/off).
2. Press the lever for the spray function (19).
Air regulation (Fig. 19)
The product has an air control (20a) with which the suc-
tion capacity can be adjusted.
1. To do this, move the air regulation (20a) on the han-
dle (20) until the desired air regulation is reached.
Wet vacuuming
• Use the foam filter (33) for wet vacuuming.
• Ensure that the foam filter (33) is correctly fitted.
• If the stainless steel container (1) is full, the safety
float valve (3c) closes the suction port and suction
operation is interrupted.
m Attention!
The product is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(33) provided.
Suction washing (Fig. 18)
Only use the washing nozzle with hard surface attach-
ment (26) or the washing nozzle for upholstery cleaning
(27) for vacuum washing.
Use the foam filter (33) for wet vacuuming. Ensure that
it is correctly fitted.
1. Fill the water tank (9).
2. Pull (do not push!) the nozzle (26, 27) in stripes
over the carpet / upholstery. Allow the stripes to
overlap slightly to ensure thorough cleaning.
3. Press the spray function lever (19) on the handle
part to switch on the spray function.
4. Empty the stainless steel container (1) immediate-
ly after vacuuming, as it is not designed to store
liquids.
11. Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
www.scheppach.com GB | 25