Scheppach FBCC12TPDF Originalbetriebsanleitung Seite 31

• If the wood is extremely overgrown, split the trunks
from the outline.
Attention: Certain types of wood can come un-
der a lot of tension during splitting and crack
abruptly.
Knock out jammed wood against the splitting
•
direction.
10.8 Operation of the trunk lifter (6) (fig. 10)
General information about the trunk lifter (6)
• The chain (6a) of the trunk lifter (6) may only be
attached to the splitting blade using the last link for
safety reasons.
• Ensure that no other people are present in the
working range of the trunk lifter (6).
10.9 Operation of the trunk lifter (6) (fig. 10)
1. Release the retaining hook of the trunk lifter so
that the lifting tube can run freely.
2. Move the splitting blade down until the lifting tube
of the trunk lifter lies completely on the foor.
3. In this position, you can roll the trunk to the split
onto the lifting tube.
4. The trunk must lie in the area between the two
fixing points.
5. Push the return bar (3) down and let the splitting
blade (4) move up.
6. Caution! Do not stand in the working range of
the trunk lifter (6)! Danger of injury!
7. Now align the trunk, press it against the claw (14)
and split it. (Refer to: Working instructions)
8. Then remove the split wood and move the splitting
blade (4) and thus the trunk lifter (6) down again.
9. A new log can now be rolled onto the trunk lifter (6).
10.10 Resetting the trunk lifter (6) (fig. 10)
This is used as a second guard arm when not us-
ing the trunk lifter (6). To do this, the trunk lifter (6) is
raised until it engages on the retaining hook (12).
10.11 Trunk lifter (6) transport position (fig. 10)
Guide the trunk lifter (6) up by hand until it latches into
place in the retainer hook (12).
Observe these instructions to ensure that you
can work quickly and safely.
11. Cleaning
Only carry out modifications, adjustments and clean-
ing work when disconnected from the drive shaft.
We recommend that you clean the product directly
after every use.
Wipe chippings and dust off the product from time to
time with a cloth.
Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product. Make sure that no water can
penetrate the interior of the product.
12. Transport
The product can be easily transported using the
3-point attachment on the drive vehicle.
Before transporting the product, place it in the trans-
port position.
To do this, move the splitting blade (4) downwards un-
til it rests on the support (4a). Then remove both safe-
ty pins and their split pins (1a) and move the hydraulic
cylinder down into the transport position by pressing
the return bar (3) downwards.
Make sure there is sufficient manoeuvring space when
driving, e.g. when turning, parking and at junctions.
Before transport, ensure that the product is properly
and securely attached to the drive vehicle and that
the cardan shaft has been disassembled.
Never transport the product with the cardan shaft
drive connected.
Make sure that the product is raised high enough to
pass obstacles during transport.
13. Storage
Store the product and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C.
Store the tool in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
14. Maintenance
Attention!
Ensure that the cardan shaft is not connected to the
drive vehicle.
Oil change intervals
Initial oil change after 50 operating hours, then every
250 operating hours.
14.1 Changing oil (fig. 17 + 18)
Due to the heavy weight of the product, we rec-
ommend that maintenance work is carried out by
at least two people.
1. Move the additional transport wheel (5) to the
transport position.
2. Use the transport wheels (9) to tilt the product so
that you can easily reach the oil drain plug (19).
3. Place an appropriately sized container under the
oil drain screw (19).
GB | 31