Start-Up; Electrical Connection - Scheppach Mix200 Originalbetriebsanleitung

low through the spring and connect it to the extension
rod.
Fitting the frame with wheel support (Enclosed ac-
cessories bag (C) Fig. 6
Mount frame and wheel support cpl. with 2 hexagonal
bolts M8x70, 2 washers 8 mm, 2 spring washers, 2 nuts
M8. Tighten the screw firmly.
Fitting the drum lower section with frame (En-
closed accessories bag (D) Fig. 7
Place the drum lower section (g) with bearing holder (f)
on the pre-assembled frame, tighten with 2 hexagonal
bolts M8x20, 2 washers, 2 spring washers and 2 nuts
M8.
Secure with Ø42 spiral ring. Fix opposite side in place
with locking plate and 2 M8x65 hexagonal bolts.
Fitting mixing unit (Enclosed accessories bag (E)
Fig. 8
Secure the mixing plant (u) with 2 Phillips screws
M10x20 to the drum lower section with 2 washers, 2
spring washers and 2 nuts M10. Insert a rubber washer
between the mixing plant and the drum.
Fitting the drum upper section (Enclosed accesso-
ries bag (F) Fig. 9
Place the rubber ring on the lower section. Put on the
drum upper section.
Attention! The glued-on arrows mark the exact align-
ment of the drum lower and upper sections. Align the
drum upper section and fit it to the drum lower section
using M8x20 hexagonal bolts with washers and spring
washers, then tighten. Secure the mixing plant (i) with
2 Phillips screws M10x20 and 2 locking washers to the
drum lower section with 2 washers, 2 spring washers
and 2 nuts M10. Insert a rubber washer between the
mixing plant and the drum.
Fitting the swivel wheel (Enclosed accessories
bag (G) Fig. 10
Fit the swivel wheel and the locking washer to the out-
er flange using two M8x20 hexagonal bolts, washers,
spring washers and locknuts.
Fitting the engine housing (Enclosed accessories
bag (H) Fig. 11
Place the engine housing on the retaining plate, secure
with 2 M8 safety nuts incl. washers. Fix to frame with
M8x70 hexagonal bolt.
24 | GB
9.

Start-up

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Only operate the concrete mixer if no parts (e.g.
protective covers) are missing or faulty and if the
connection cable is not damaged.
Setting up:
• Set up the concrete mixer horizontally on level, firm
ground.
• Do not set up the concrete mixer on the connection
cable!
• Lay the connection cable so that it cannot be kinked,
crushed or damaged in any other way.
Note:
The drum must be able to swivel to the right and
left. There must be space under the drum for a
wheelbarrow to empty it.
Switching on:
• Plug the device into the socket Switch on to "I"
(green button)/switch off to "0" (red button).
Adjusting the drum
• To adjust the drum, pull back the hand wheel so that
you can move the drum.
• When the drum is in the desired position, engage the
hand wheel again.
Filling (Fig. 12a + 12b)
• Before filling, make sure that the opening of the drum
is aligned so that no mix can fall out of the drum.
• Fill the mix while the drum is running.
• (Do not overfill the drum)
Caution! Danger from moving parts
Emptying (Fig. 13a)
• To empty the drum, swivel it downwards.
• Make sure that a sufficient container (e.g. wheelbar-
row) is present under the drum.
• Make sure that no mix can get onto the floor.

10. Electrical connection

The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
www.scheppach.com