GRAPHITE 58GE145 Benutzerhandbuch Seite 8

• Do not use a battery that is damaged or modified. Damaged or
modified batteries may act unpredictably, leading to fire, explosion or
danger of injury.
The battery must not be exposed to moisture or water.
• Always keep the battery away from a heat source. D o not leave it in
a high temperature environment for long periods o f
direct sunlight, near radiators or anywhere where the temperature
exceeds 50°C).
• Do not expose the battery to fire or excessive temperatures.
Exposure to fire or temperatures above 130°C may cause an explosion.
NOTE: A temperature of 130°C can be specified as 265°F.
All charging instructions must be followed, and the battery must not
be charged at a temperature outside the range specified in the rating
data table in the operating instructions. Charging incorrectly or at
temperatures outside the specified range can damage the battery and increase the
risk of fire.
BATTERY REPAIR:
• Damaged batteries must not be repaired. Repairs to the battery are
only permitted by the manufacturer or an authorised service centre.
• The used battery should be taken to a disposal centre for this
type of hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water. The
ingress of water into the charger increases the risk of shock. The
charger may only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any maintenance
or cleaning.
• Do not use the charger placed on a flammable surface (e.g.
paper, textiles) or in the vicinity of flammable substances. Due
to the temperature increase of the charger during the charging
process, there is a danger of fire.
• Check the condition of the charger, cable and plug each time
before use. If damage is found - do not use the charger. Do not
attempt to disassemble the charger. Refer all repairs to an
authorised service workshop. Improper installation of the charger may
result in a risk of electric shock or fire.
• Children and physically, emotionally or mentally challenged persons,
as well as other persons whose experience or knowledge is
insufficient to operate the charger with all safety precautions, should
not operate the charger without the supervision of a responsible person.
Otherwise there is a danger that the device will be mishandled resulting
in injury.
When the charger is not in use, it should be disconnected
from t h e mains.
All charging instructions must be followed, and the battery must not
be charged at a temperature outside the range specified in the rating
table in the operating instructions. Charging incorrectly or at
temperatures outside the specified range can damage the battery and
increase the risk of fire.
CHARGER REPAIR
• A defective charger must not be repaired. Repairs to the charger
are only permitted by the manufacturer or an authorised service centre.
ATTENTION: The device is designed for indoor operation.
Despite the use of an inherently safe design, the use of safety
measures and additional protective measures, there is always
a residual risk of injury during work.
Li-Ion batteries can leak, catch fire or explode if they are
heated to high temperatures or short-circuited. Do not store
them in the car during hot and sunny days. Do not open the
battery pack. Li-Ion batteries contain electronic safety devices
which, if damaged, can cause the battery to catch f i r e
explode.
PICTOGRAMS AND WARNINGS
t i m e (in
Read the operating instructions, observe the warnings and safety
conditions contained therein!
Wear personal protective equipment: safety goggles, protective
mask, hearing protection.
Before repairs, maintenance, disconnect from the power supply by
removing the battery.
For indoor use.
Use personal protective equipment: protective gloves.
Keep out of the reach of children.
Protect from moisture.
Selectively recyclable
Do not dispose of with household waste
DESCRIPTION OF THE GRAPHIC ELEMENTS
The numbering below refers to the components of the device
shown on the graphic pages of this manual.
Designation
1
2
3
4
5
6
7
8
9
10
11
12
13
14
* There may be differences between the graphic and the actual
product
CONSTRUCTION AND APPLICATION
The jigsaw is a hand-held device powered by a battery. It is driven by a
brushless DC motor. The machine is designed for making straight split cuts,
curved cuts and notches in wood, wood-based materials and plastics and
metals (p r o v i d e d a
are renovation and construction work as well as all DIY (do-it-yourself)
w o r k .
Do not misuse the device
OPERATION OF THE DEVICE
BLADE MOUNTING
The blade is mounted and replaced without tools.
NOTE: Use blades with a T clamping system.
Blade mounting
• Lift the cover Fig. A 14.
or
• Then turn the lever on the blade holder Fig. B4 to the right as far as
it will go (Fig. B4).
•
Insert the blade as far as it will go into the blade holder Fig. A3 (the
teeth of the blade should point forward) and release the handle
lever
Important! Ensure that the saw blade is properly seated in the guide
roller Fig. B
• Once you have ensured that the blade is installed correctly, you
can proceed.
Removing the saw blade
Removal of the blade is done in the reverse order of installation.
DUST EXTRACTION
8
Description
Vertical handle
Switch
Blade holder
Parallel guide fixing knob
Speed controller
Horizontal handle
Rotary knob for the pendulum movement (trim
function)
Jigsaw blade
Battery socket
Dust extraction port
Cutting angle setting lock
Cutting angle setting plane
Blow direction switch
Plexiglas cover
suitable saw blade is used). Its areas of use
3.