Chassis L ayout (TopView) Chassis-Anordnung (Oberansicht) Installation du chassis(vue de dessus) C003, SMOOTHING CAPACITOR PROTECTION PC BOARD INRUSH CURRENT ABSORBER BOARD RY201, SPEAKER RELAY POWER SUPPLY PC BOARD POWER METER, R-CH SPEAKER A TERMINALS TOOL, POWER TRANSFORMER FUSES PC BOARD POWER METER, L-CH...
Adjustment meter between pins 17 and E2 on Driver PC board. Instruments: Audio Generator, HD Analyzer, AC Volt- If the meter needle does not deflect in normal direc- meter,DC Voltmeter,LoadResistors of 8 ohms(250 tion, reverse the polarity. watts) and 2 ohms (250 watts). Adjust potentiometerVR101on Driver PCboard so Note: The unit goes into operation (Protection Indi-...
Seite 4
IDLING CURRENT ADJUSTMENT 2. Adjust potentiometer VR102 on Driver PC board to Leave the input terminals short-circuited. Connect DC Voltmeter between pins 15 and 16 on Driver PC obtain 140mV reading on DC Voltmeter. Make the same adjustment for the other channel board (minus lead to pin 15 and plus lead to pin 16).
Seite 5
Ill. EINSTELLEN DES ÜBERLASTUNGSSCHUTZES schlossen werden, auf OFF schaltet. NehmenSie dieseEinstellung für den rechten und linken Stellen Sie den Netzschalter auf OFF, um den Schutz- Kanal getrennt vor. (Führen Sie das Signalnur dem schaltkreisfreizugeben,und dann zurück auf ON. einzustellenden Kanal zu). Stellen Sie den Ausgangspegel des Tongenerator so 1.
Seite 6
WATTMETER CALIBRATION 1. Connect an 8-ohm load resistor to speaker terminals. Adjust input level so that AC Voltmeter reads 31 Connect Voltmeter in parallel with the load volts. Adjust potentiometer VR401 (VR402 for R-ch) on resistor. Connect Audio Generator to input terminals, Meter Amplifier PC board to obtain 120 watts on...
Specification Technische Daten Caractéristiques 120watts* perchannelRMSboth channels drivenat 8 ohms Continuous Power Output (or4 ohms) f rom20to 20,000Hz w ith nomorethan0.01% total harmonic distortion. No more than 0.01% (continuous rated power output). Total Harmonic Distortion No more than 0.006% (60 watts perchannelpower output at 8-ohm load).
Seite 8
Addendum Nachtrag Addenda carefully the shape of the band printed on the I. IC (HA-12002) used in the protection circuit been changedto a new IC marked HA-12002W* molding. See Marking Of IC in Fig. A. As the circuit constant IC is different HA•12002W is listed in the repair parts noted in this from conventional ones, when using the new IC, be...
Seite 9
2. Der Überlastungs-DetektorschaItkreis ist modifiziert Erforderliche Teile: Schematic Diagran worden. Diese Änderung gilt flir alle Einheiten mit I) Befestigungsplatte flir die PC-Platte: Teil Nr einer Seriennummer von NB80100 und darüber. numbers NB80100 120012231 a) Der neue Überlastungsschutzkreiserspart die 2) SchraubeO 3x6mm: Teil Nr.
RepairParts List • Schematic Diagram (Overload Detector Circuit Portion): Applicable to units with serial numbers NB80100 or over. Reparaturteilliste • SchematischesDiagramm (Uberlastungs-Detektorschaltkreis): Gilt für Geräte mit einer Liste despiécesde rechange Seriennummer NB80100 Oder darüber. • Diagramme schématique (Portion du circuit de détection de surcharge): concerne les appareils avant des numéros de Série NB80100 et au dessus.
SchematicDiagram Schaltungsschema Diagramme schématique Schematic Part Description Location Rt28 PROTECTION CIRCU 770911210 Screw, 8 x 70mm, PT Mtg 770402211 Nut, M8, Hex, PT Mtg R129 0108 , G109 770500031 Flat Washer, $9 x 018 x R20' tl .6, PT Mtg 2SA921 se.sv R 144...
Seite 12
MODEL RB-200C SCHEMATIC DIAGRAM (X -267) POWER METER CIRCUIT POWER METER PROTECTION CIRCUIT ( X-263) 0403 2SC1980 POWER TRANSFORMER ( T-IIOC) 5.6K 0407 T 001 POWER SW. R201 .0.2V 1S2472 MOOI L ch 0." LINE a 401 R202 a 001 ct.03 R 407 IC401 NJM 4558...