R&G RSET32 Montageanleitung Seite 21

Page 21 of 21
•
Die Montageplatte und zwei M8 Schrauben, die in Abbildung 17 abgebildet sind, passend einstellen.
UM EINE BESCHADIGUNG DER BREMSLEITUNG ZU VERMEIDEN, DARF DIE GANZ LINKE REIHE DER
ÖFFNUNGEN FÜR DIE EINSTELLUNG DER FUSSRASTE NICHT BENUTZT WERDEN.
BREMSLICHTSCHALTER
• Entfernen Sie die Hohlschraube am Hauptbremszylinder und ersetzten Sie diese durch den mitgelieferten
Bremslichtschalter (Artikel 6) –verwenden Sie die neuen Dichtungsringe (Artikel 7), wie in Abbildung 18
DAS BREMSSYSTEM MUSS DANACH ENTLÜFTET WERDEN!
abgebildet.
• Wir empfehlen, die original Verkabelung zu schneiden und die Kabelverbindungen vom Kit (Artikel 8) zu
verwenden, um die Bremslichtschalter mit der original Verkabelung zu verbinden – siehe Abbildung 19.
BITTE DIE ORDNUNGSGEMÄSSE FUNKTION DER BREMSEN / DES BREMSLICHTS ÜBERPRÜFEN, BEVOR SIE
MIT DEM MOTORRAD FAHREN.
Bedingt durch die Komplexität und Gefahr, die bei jeglicher Arbeit an der Bremsanlage besteht, empfehlen
wir Ihnen, den Einbau von einer qualifizierten Fachwerkstatt durchführen zu lassen!
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall
conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it has chosen
the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the
workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to
original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Tel: +44 (0) 420 89007 Fax: +44 (0)
1
Abbildung 18
AUSGABE 3
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit , Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 8730
1
Abbildung 19
05/07/2021 (DM)
CONSUMER NOTICE
R&G
www.rg-racing.com
1
Email: info@rg-racing.com
RSET32
HINWEIS: