Safety Instructions; Lenze Controllers; General Safety And Application Notes For Lenze Controllers - Lenze 8200 motec Montageanleitung

Show/Hide Bookmarks

Safety instructions

1

Lenze controllers

6.

General safety and application notes for Lenze controllers

(according to Low-Voltage Directive 73/23/EEC)
1. General
Lenze controllers (frequency inverters, servo inverter, DC controllers) can carry a voltage or parts of the controllers
can rotate during operation. Surfaces can be hot.
If the required cover is removed, the controllers are used inappropriately or installed or operated incorrectly, severe
damage to persons or material assets can occur.
For more information please see the documentation.
All operations concerning transport, installation, and commissioning as well as maintenance must be carried out by
qualified, skilled personnel (IEC 364 and CENELEC HD 384 or DIN VDE 0100 and IEC report 664 or DIN VDE 0110 and
national regulations for the prevention of accidents must be observed).
According to this basic safety information qualified, skilled personnel are persons who are familiar with the assembly,
installation, commissioning, and operation of the product and who have the qualifications necessary for their
occupation.
2. Intended use
Drive controllers are components which are designed for the installation into electrical systems or machinery. They
are not to be used as domestic appliances, but only for industrial purposes according to EN 61000-3-2. The
documentation contains information about the compliance of the limit values to EN 61000-3-2.
When installing controllers into machines, commissioning of the drive controllers (i.e. the starting of operation as
directed) is prohibited until it is proven that the machine corresponds to the regulations of the EC Directive 98/37/EG
(Machinery Directive); EN 60204 (VDE 0113) must be observed.
Commissioning (i.e. starting of operation as directed) is only allowed when there is compliance with the EMC Directive
(89/336/EEC).
The drive controllers meet the requirements of the Low-Voltage Directive 73/23/EEC. The harmonised standards EN
50178/DIN VDE 0160 apply to the controllers.
The technical data as well as the connection conditions can be obtained from the nameplate and the documentation.
The instructions given must be strictly observed.
Warning: Controllers are products with restricted availability according to EN 61800-3. These products can cause
interferences in residential premises. If controllers are used in residential premises, corresponding measures are
required.
3. Transport, storage
The notes on transport, storage and appropriate handling must be observed.
Climatic conditions according to EN 50178 apply.
4. Installation
The controllers must be installed and cooled according to the regulations given in the corresponding Instructions.
Ensure careful handling and avoid mechanical overload. Do not bend any components and do not change the
insulation distances during transport and storage. Electronic components and contacts must not be touched.
Controllers contain electrostatically sensitive components which can easily be damaged by inappropriate handling.
Do not damage or destroy any electrical components since this could mean hazards for your health!
5. Electrical connection
When working on live controllers, the valid national regulations for the prevention of accidents (e. g. VBG 4) must
be observed.
The electrical installation must be carried out in compliance with the corresponding regulations (e.g. cable
cross-sections, fuses, PE connection). Additional notes and information can be obtained from the corresponding
Instructions.
The Instructions contain notes concerning wiring according to EMC regulations (shielding, earthing, filters and cable
routing). These notes must also be observed when using CE-marked controllers. The compliance with limit values
required by the EMC legislation is the responsibility of the manufacturer of the machine or system.
6. Operation
If necessary, systems including controllers must be equipped with additional monitoring and protection devices
according to the applying safety regulations (e.g. regulation for technical equipment, regulation for the prevention
of accidents). The controller can be adapted to your application. Please observe the corresponding information given
in the Instructions.
After a controller has been disconnected from the voltage supply, all live components and power connections must
not be touched immediately because capacitors can still be charged. Please observe the corresponding stickers on
the controller.
2
EDK82MV222 DE/EN/FR 3.0
L