Makita LH1040 Bedienungsanleitung Seite 15

CAUTION:
Do not apply excessive pressure on the handle
•
when cutting. Too much force may result in
overload of the motor and/or decreased cutting
efficiency. Push down handle with only as much
force as is necessary for smooth cutting and
without significant decrease in blade speed.
Gently press down the handle to perform the cut. If
•
the handle is pressed down with force or if lateral
force is applied, the blade will vibrate and leave a
mark (saw mark) in the workpiece and the
precision of the cut will be impaired.
1. Press cutting
Fig.41
Secure the workpiece against guide fence and
turn table. Switch on the tool without the blade
making any contact and wait until the blade attains
full speed before lowering. Then gently lower the
handle to the fully lowered position to cut the
workpiece. When the cut is completed, switch off
the tool and WAIT UNTIL THE BLADE HAS
COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
2. Miter cutting
Refer to the previously covered "Adjusting the
miter angle".
3. Bevel cut
Fig.42
Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered
"Adjusting the bevel angle"). Be sure to retighten
the lever firmly to secure the selected bevel angle
safely. Secure the workpiece against guide fence
and turn table. Switch on the tool without the blade
making any contact and wait until the blade attains
full speed. Then gently lower the handle to the
fully lowered position while applying pressure in
parallel with the blade. When the cut is completed,
switch off the tool and WAIT UNTIL THE BLADE
HAS COME TO A COMPLETE STOP before
returning the blade to its fully elevated position.
CAUTION:
Always be sure that the blade will move down to
•
bevel direction during a bevel cut. Keep hands out
of path of saw blade.
During a bevel cut, it may create a condition
•
whereby the piece cut off will come to rest against
the side of the blade. If the blade is raised while
the blade is still rotating, this piece may be caught
by the blade, causing fragments to be scattered
which is dangerous. The blade should be raised
ONLY after the blade has come to a complete stop.
When pressing the handle down, apply pressure
•
parallel to the blade. If the pressure is not parallel
to the blade during a cut, the angle of the blade
might be shifted and the precision of the cut will be
impaired.
4. Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter
angle is being cut on a workpiece. Compound
cutting can be performed at angle shown in the
table.
Bevel angle
45
006366
When performing compound cutting, refer to
"Press cutting", "Miter cutting" and "Bevel cut"
explanations.
5. Cutting aluminum extrusion
Fig.43
When securing aluminum extrusions, use spacer
blocks or pieces of scrap as shown in the figure to
prevent deformation of the aluminum. Use a
cutting lubricant when cutting the aluminum
extrusion to prevent build-up of the aluminum
material on the blade.
CAUTION:
Never attempt to cut thick or round aluminum
•
extrusions. Thick aluminum extrusions may come
loose during operation and round aluminum
extrusions cannot be secured firmly with this tool.
Never cut aluminum in the table saw mode (bench
•
mode).
6. Wood facing
Use of wood facing helps to assure splinter-free
cuts in workpieces. Attach a wood facing to the
guide fence using the holes in the guide fence.
See the figure concerning the dimensions for a
suggested wood facing.
Over 10mm
1
90mm
1. Hole
005577
CAUTION:
Use straight wood of even thickness as the wood
•
facing.
Use screws to attach the wood facing to the guide
•
fence. The screws should be installed so that the
screw heads are below the surface of the wood
facing.
15
Miter angle
Left and Right 0 - 45
Over 460mm
107mm 90mm
107mm
1