Additional Battery Safety Warnings; Residual Risks - Ryobi Rwsl1801 Originalanleitung

LOWER GUARD FUNCTION
■
Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or
tie the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or any
other part, in all angles and depths of cut.
■
Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
■
Lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released. For all other sawing, the lower guard
should operate automatically.
■
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor.
An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop after
switch is released.
ADDITIONAL SAFETY WARNINGS
■
Wear a face or dust mask if the operation is dusty.
■
Do not use any abrasive wheels.
■
Use only saw blades recommended by the
manufacturer, which conform to EN 847-1, if
intended for wood and analogous materials.
■
Avoid overheating the blade tips. Do not use dull or
damaged blades. Do not force the tool.
■
Do not use blades of larger or smaller diameter than
recommended.
■
Wear ear protection.
■
Use only blade diameter(s) in accordance with the
markings.
■
Identify the correct saw blade to be used for the material
to be cut.
■
Use only saw blades that are marked with a speed
equal or higher than the speed marked on the tool.
■
Wear a dust mask.
■
Ambient temperature range for tool during operation is
between 0°C and 40°C.
■
Ambient temperature range for tool storage is between
0°C and 40°C.
■
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
LASER SAFETY RULES
■
The laser radiation used in this saw is Class 2 with
maximum ≤1 mW and 650 nm wavelengths. Do not
4
Original Instructions
stare into the laser beam. Failure to comply with the
rules could result in serious personal injury.
■
Do not stare into beam during operation.
■
Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
■
Do not place the laser in a position that may cause
anyone to stare into the laser beam intentionally or
unintentionally.
■
Do not use optical tools to view the laser beam.
■
Do not operate the laser around children or allow
children to operate the laser.
■
Do not attempt to repair the laser device by yourself.
■
Do not attempt to change any parts of the laser device
by yourself.
■
Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
■
Do not replace the laser with a different type.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0°C and 40°C.
■
Ambient temperature range for battery storage is
between 0°C and 20°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
■
Injury caused by kickback
– Read and understand the information in this manual.
■
Injury caused by vibration
– Limit exposure. See "Risk Reduction".