Assembly; Assembling/Disassembling; Mounting The Handle; Mounting The Carrying Strap - ATIKA BAE 30 Betriebsanleitung
Vorschau ausblenden
Andere Handbücher für BAE 30:
- Montage- und bedienungsblatt (12 Seiten) ,
- Originalbetriebsanleitung (140 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
56
Chain wheel
57
Chain stretching screw
58
Chain stretching pin
59
Oil tank lock
60
Protective cap
61
Zerk fitting
62
Accessories bag
Installation tools
A
A
A
s
s
e
m
b
l
i
n
g
A
s
s
e
m
b
l
i
n
g
Remove the protective cap (60) and slide the
brushcutter (28), hedge trimmer (44) or pruner (49)
attachement tool in the holder (a) of the drive unit (1) as
shown.
Make sure that it engages with a click.
Firmly tighten the clamping screw (2).
To disassemble the attachment tool loosen the hand screw.
Press on the button (b) and pull the attachement tool out of
the holder.
Reattach the protective cap (60).
M
o
u
n
t
i
n
g
M
o
u
n
t
i
n
g
Put the drive unit (1) on a level surface.
Remove the screws (c) together with the spring rings
and washers.
Slide the lower handle (5) in the rubber sleeve (6) on
the tube shaft of the drive unit (1).
Slide the handle (4) in the lower handle and secure both
parts using the screws, spring rings and washers.
M
o
u
n
t
i
n
g
M
o
u
n
t
i
n
g
Hook the carrying strap (7) in the suspension eye (d).
A
s
s
e
m
b
l
i
n
g
t
h
e
b
A
s
s
e
m
b
l
i
n
g
t
h
e
b
M
o
u
n
t
i
n
g
t
h
e
M
o
u
n
t
i
n
g
t
h
e
Remove the 4 screws (e) together with the spring rings,
washers and nuts from the protective hood holder (31).
Loosen the hexagon socket screw (f) and fold up the holder
(32).
Slide the protective hood (30) on its holder (31).
Fold down the holder (32) and secure the protective
hood using the screws, washers and nuts. Tighten the
hexagon socket screw (f) again.
386160
386184
386174
386183
s
s
e
m
b
l
y
s
s
e
m
b
l
y
/
d
i
s
a
s
s
e
m
b
l
i
n
g
/
d
i
s
a
s
s
e
m
b
l
i
n
g
t
h
e
h
a
n
d
l
e
t
h
e
h
a
n
d
l
e
t
h
e
h
a
n
d
l
e
t
h
e
h
a
n
d
l
e
r
u
s
h
c
u
t
t
e
r
/
g
r
a
s
s
t
r
i
m
r
u
s
h
c
u
t
t
e
r
/
g
r
a
s
s
t
r
i
m
p
r
o
t
e
c
t
i
v
e
h
o
o
d
p
r
o
t
e
c
t
i
v
e
h
o
o
d
Align the hole in the protective cover (33) with the hole
on the angular gear (34) and lock the drive shaft using the
Allen key (23).
/
(22).
Left-hand thread
Remove the cover (36) and the spacer washer (37).
Put on the cutting blade (38).
The further assembly is now done in reverse sequence.
Align the hole in the protective cover (33) with the hole
on the angular gear (34) and lock the drive shaft using the
Allen key (23).
/
(22).
Left-hand thread!
Remove the cover (36) and the spacer washer (37).
Screw the thread spool (39) on the drive shaft.
Left-hand thread!
I
n
s
t
a
l
l
I
n
s
t
a
l
l
Risk of injury!
Wear protective gloves when working on the guide
bar and the saw chain.
Place the power pruner on a level surface.
Remove the securing nut (55) and remove the cover (54).
Turn the chain stretching screw (57) anticlockwisely
until the chain stretching pin (58) is at the rear end of the
thread.
m
e
r
m
e
r
Put the saw chain over the clutch (52) on the chain
wheel (50) and insert it in the circumferential guiding groove
of the guide bar.
Attend to the correct running direction of the chain links.
Place the guide bar (50). The chain stretching pin (58)
must engage in the provided chain stretching hole (g) in the
guide bar.
When assembling, pay attention that the chain links are
lying correctly within the guide slot and on the chain wheel
(56).
Remount the cover (54) and tighten the securing nut
(55) hand-tight.
Stretch the saw chain as described in section „Stretching the
saw chain".
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
c
c
u
u
t
t
t
t
i
i
n
n
g
g
b
b
Remove the hexagon nut (35) using the wrench
Assembling the thread spool
Remove the hexagon nut (35) using the wrench
A
s
s
e
m
b
l
i
n
g
t
h
e
p
o
w
A
s
s
e
m
b
l
i
n
g
t
h
e
p
o
w
i
n
g
t
h
e
g
u
i
d
e
b
a
r
a
n
d
t
h
i
n
g
t
h
e
g
u
i
d
e
b
a
r
a
n
d
t
h
l
l
a
a
d
d
e
e
e
r
p
r
u
n
e
r
e
r
p
r
u
n
e
r
e
s
a
w
c
h
a
i
n
e
s
a
w
c
h
a
i
n
31
Werbung
Kapitel
Inhaltsverzeichnis
