HIKOKI R36DA W4Z Bedienungsanleitung Seite 9

UNPACKING
Carefully unpack the power tool.
CHARGING
Battery and battery charger are not included with this
product.
For rechargeable batteries, please charge in according
to the handling instructions of the charger which you are
using.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
(sold separately)
Dismounting the dust case
Dismounting the fi lter
Check the fi lter *1
Mounting the fi lter
*2
Mounting the dust case
*3
Switch operation
*4
How to use
*5
Emptying the dust case
*6
Eff ectively removing dust
Selecting accessories
*1 a. Filter free of debris and dust
b. Rubber not deteriorated
c. Connector free of damage
*2 If the fi lter is not properly fi tted, dirt or grime can enter
the fan unit and cause damage or malfunction.
*3 The dust case can also be installed with the nozzle
facing upwards. (Fig. 7-a)
*4
Continuous operating time
Mode
3 (HIGH) Approx. 15 min.
2 (MID) Approx. 30 min.
1 (LOW) Approx. 60 min.
∗ Continuous operating time will vary according
to battery condition. Please use the table as a
guideline.
NOTE
○ To suppress noise when using the appliance,
switch to 1 mode.
○ When using 3 mode on certain surfaces, such as
carpets, the suction force may make the action feel
heavy. If this occurs, switch to 2 or 1 mode instead.
*5 When attaching the nozzle or extension pipe, insert as
you twist in the direction indicated by the arrow.
Twist in the direction indicated by the arrow when
detaching as well. (Fig. 10-a)
Twisting in the opposite direction could result in
detaching the dust case from the housing.
*6 NOTE
○ Point the intake port downward as dust can spill
when removing the dust case.
○ If the suction does not recover after disposing the
dust, clean the fi lter. (See "Cleaning the fi lter" on
page 9.)
Figure Page
2
3
4
5
6
7
8
10
11
*7 12
―
BSL36A18
*7 The appliance has a built-in mechanism for scraping
off dust attached to the fi lter when removing the dust
case.
To even more eff ectively scrape off the dust, repeatedly
turn the dust case back and forth (2 to 3 times or more).
Holding the unit so that the dust case does not detach
from the housing, slightly and repeatedly turn the dust
case in the indicated directions.
THE INDICATOR LAMP (Fig. 9)
Notice about fi lter cleaning
If the fi lter becomes clogged and suction power decreases,
the indicator lamp will illuminate, and the LED light will
fl ash.
If this happens, promptly empty the dust case and clean
the fi lter. (See Fig. 11, Fig. 12, and "MAINTENANCE AND
INSPECTION" on page 9.)
2
Notice about intake port blockage
2
If the intake port becomes blocked during use - for example
2
while vacuuming carpets - the main unit will make a pulsing
2 sound, the indicator lamp will illuminate, or the LED light will
fl ash. However, this is not a sign of a fault.
3
Clear the blockage from the intake port if this happens.
NOTE
3
When the indicator lamp illuminates, the appliance will
3
switch automatically to Safe Mode, running at reduced
4
power to protect the motor and rechargeable battery.
The appliance will stop automatically if Safe Mode
5
continues for a preset duration.
5
MAINTENANCE AND INSPECTION
132
WARNING
○ For inspection and maintenance, be sure to turn off the
switch and disconnect the battery.
○ Do not work with wet hands. May cause electric shock
or injuries.
1. Cleaning the fi lter
CAUTION
○ Do not wash the fi lter in a washing machine.
○ Do not wash the fi lter in hot water or dry it by fi re.
○ Do not detach the fan fi lter and the fi lter holder.
If the vacuuming effi ciency is poor even when the dust
case has been emptied, remove the fi lter and wash it in
cold or warm water. (The water should not be hot to the
touch.)
After washing, dry out of direct sunlight. (Fig. 13-a)
If there is dust on the fan fi lter, hold the cleaner with the
fan fi lter pointing downwards to keep dust from entering
the motor and lightly clean with a small brush such as a
used toothbrush. Do not brush vigorously. (Fig. 13-b)
NOTE
○ Do not use gasoline, thinner, benzene or kerosene as
they can melt plastic.
○ Do not use an air gun or similar tool to clean the fi lter,
fan fi lter or the appliance itself. (Fig. 13-c)
Doing so could push dirt into the appliance and cause
malfunction.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
9
English