Cleaning; Transport; Storage/Hibernation; Maintenance - Scheppach Rrma300 Bedienungs- Und Sicherheitshinweise

3. Press OK to activate or deactivate the zone
mowing function.
4. This function allows the robot to mow certain
zones of the lawn in a targeted manner, which is
particularly useful in complex gardens or areas
with different usage.

10. Cleaning

m ATTENTION
Switch off the product before cleaning with the
m ATTENTION
Put on protective gloves before cleaning the rotating
blade carrier.
We recommend that you clean the product directly
after every use.
Clean the product at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
agents or solvents; they could corrode the plastic parts
on the product. Make sure that no water can penetrate
into the product interior.

11. Transport

• Press the -button ("POWER ON/OFF" button) to
switch off the robotic lawnmower (1).
• Wear protective gloves when transporting the ro-
botic lawnmower (1).
• Carry the robotic lawnmower (1) securely with both
hands.
To prevent damage, avoid the robotic lawnmower (1)
falling to the ground from greater heights.
If this does happen, it must be immediately taken to a
specialist workshop for inspection.
Do not continue to use the robotic lawnmower (1) be-
fore this has been done.

12. Storage/Hibernation

Your mower will give you pleasure for longer if it is
allowed to hibernate.
Although this is not a problem, we recommend that
you store your mower in a closed room, e.g. in the
garage, during the winter.
Before storing the mower:
• Clean it thoroughly (see point 10)
• Charge the battery fully.
• Switch the product off.
Store the product and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 10
and 20 ˚C.
Store the robotic lawnmower (1) in its original pack-
aging.
Cover the robotic lawnmower (1) to protect it from
dust and moisture.
Store the operating manual with the robotic lawn-
mower (1).

13. Maintenance

m ATTENTION
button. Disconnect the mains plug before carrying out any
maintenance work.
Connections and repairs
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the
event of any enquiries:
• Machine data - type plate
13.1 Replacing the blade (7) (Fig. 25)
m ATTENTION
Switch the mower off before starting with the work.
m NOTE
The blades (7) must be replaced after approx. 8 weeks.
Use only original blades from the manufacturer. (Art.
no. 7913001601)
m ATTENTION
Put on protective gloves before replacing the blade (7).
m ATTENTION
All blades (7) must always be changed at the same time.
The changing of individual blades (7) is not permitted.
If the Phillips screws (8) are damaged or can no
longer be tightened, these must also be replaced.
New screws are included with the replacement blades.
• To replace the blades (7), place the robotic lawn-
mower (1) on a workbench with the underside fac-
ing upwards. (We recommend a soft base to avoid
damage to the housing).
• Loosen the Phillips screw (8) with the help of a Phillips
screwdriver (not included in the scope of delivery).
• Remove the old blade (7).
• Fit the new blade (7) and fasten it with a new screw
(8).
• Check that the blade (7) can move.
If this is not the case, loosen the screw (8) a little.
• Carry out this operation on all three blades (7).
13.2 Software update (Fig. 26)
The software can be updated as soon as a new ver-
sion is available. (The latest software version can be
found on our homepage www.scheppach.com).
www.scheppach.com
GB | 29