Dimplex CFH60 Bedienungsanleitung Seite 4

Dimplex Industrial Fan Heater
Models : CFH60, CFH90 & CFH120
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT SAFETY ADVICE
DO NOT COVER OR OBSTRUCT the air intet or outlet grille.
ENSURE THE APPLIANCE IS EARTHED.
Always disconnect supply
Do not use this heater in areas
This heater must not be located immediately
socket outlet or connection
This product should be mounted safely to a solid wall.
Ensure the supply cables are of adequate current
and are protected by a suitable fuse.
This appliance should only be connected to the fixed wiring of the
premises by means of conduit.
This product must not be subjected to water spray or immersion.
If the appliance is mounted in a toilet or washroom, the appliance
should be mounted such that no part Of it can be touched
person using a fixed bath or shower.
If the appliance is mounted in a toilet or washroom an isolating
switch must be provided
entrance door.
WARNING: Isolate electrical
when carrying out maintenance.
General
A range of robust, high power wall mounting fan heaters designed to
coordinate with the Dimplex range of Air Curtains, providing environmental
heating in commercial and light industrial environments.
The heaters work by gradually raising the air temperature in the building
and shouid be positioned so as best to achieve an even temperature
distribution.
The product range has outputs of 6kW. 9kW and 12kW, and each product
contains on-board electronics
electronic control panel (CFCH) or building energy management
Connectivity between heater and control panel is achieved using LAN
(Local Area Network) cable i.e. CATS, CAT5E or CAT61pin configuration
is straight through 1 to 1
The etectronic contro\ler has a number of features inciuding thermostatic
control. For more details on these refer to the CFCH
Model Heat Electrical
Output Supply
kW
220-240V-
CFH60 3/6 220-240V-
380-41
220-240V-
CFH90 6/9 220-240V-
380-415Vm
220-240V-
CFHI 20 6/12 220-240V-
380-415V-
before working on the product.
where excessive dust exists.
above or below a fixed
box.
carrying capacity
outside the washroom adiacent
supply to ALL modular linked
that enables 'daisy-chain' linking to an
instruction
Weight
Electrical
Load
(per phase)
IPN
26.0
156 13
3PN 9.0
IPN
38.8
3P 23.0
3PN 13.3
IPN 51.6
3P 30.4 14
3PN 17.5
Wall Mounting
Removethewall mountingbracketfromthe back ofthe heaterand using
it as a guide(see Fig. 2) markoff the hotepositionson a suitablewall (a
minimumheightof 2 metersis requiredfrom the floor levetto the bottom
of the bracket).Solid brick or concrete block walls must be drilled and
plugged. Fix the wall mounting bracket to the wall and assemble the
heater to the extension tube using a bolt and wing nut fitted into hole I
shown in Fig. 3a. Rotate the heater as shown in Fig. 3b. and fix the
heaterinto positionusing the remainingbolt andwing nutin hOle2. Pivot
and rotate the heater into the desired position and tighten all three wing
nutS.A 6mm Allen key can be used as an aid to tightening the bOltS.
Electrical
Note: The installation
a competent electrician and be in accordance with the current
IEE wiring
All products are fitted with a microprocessorcontrol. Electrical power
and control connections for all CFH models are made by removing the
by a
control housingand bottompanel. The control housingCy' in Fig. 4) is
de\achedby removingthe two quick release fastenersand hinging the
housing asshown. T hebottom panel
to the two screws and lifting off as shown,
Note: A suitable local isolating switch must be provided in the electrical
supply circuit as close as possible to the heater with at least 3mm
units
clearance on each pole.
Wiring Diagrams
A PCB
Mains in terminal
B
c Cut-out
D LAN
E Elements
M Motor
Remove the large knock-out from back panel of heater and feed
appropriatesupply cable (see 'x' in Fig. 5) to terminal blocks
electrical connections as shown in Fig. 7 and fix the cable in back panel
system.
using suitablecable gland(not suppiied).By removingone of thesmaller
knock-outs and using LAN cable (see 'y' in Fig. 5) make the control
connections to BUS IN socket 'w' also shown in Fig. 5. Fix this cable in
the back panelusing a suitablecable gland(not supplied)and feedback
to the electronic control panel (CFCH) using suitable conduit if required.
leaflet. Refer to CFCH Instructions for installation and connections of electronic
controlpanel. Replacethe bottompaneland control housingand switch
on powerto heater and installedelectroniccontrol panel.Ensurethat ali
control settings function correctly.
Note: The factorysuppliedunit can accept three phasevoltage of —380-
415V.For singlephase -220-240V and three phase 020-240V referto
Min
the electricalwiringlabel (see Fig. 8) fixed to the undersideof thebottom
Installed
panel. TO change between different voltage systems, rearrange the
height
push on connectionsas per the required wiring diagram
m
Operation using Control Panel - CFCH
Switch on electrical supply to the fan heater and the electronic control
2
panel. When all units are powered up and there ISa connection between
the controller and the master unit, an LED will turn on in the controller to
indicate the units are functioning. Refer to the CFCH instruction leaflet on
the operation of the electronic control panel.
2
2
and Control connections
of this appliance should be carried out by
regulations.
inFig.4)isdetached byremoving
- see Fig. 7
blocks
circuit
Sockets
Make