Cleaning And Maintenance - Mpm Mod-22 Bedienungsanleitung

EN
5. Pour clean water into the washing liquid container (in order to check its level use the indicator of
water level (C4) and shampoo (quantity of a shampoo has been given on a bottle).
ATTENTION! When using a function of surface washing do not put water into the water filter
container (B1).
6. Reinstall the container (B1) so that the suction inlet (B8) is on the opposite side to the short wash-
ing hose socket in the washing liquid tank. Then lock the locks (D3), install the body (B2) in the
container (B1). Fit the motor unit and lock the locks (B6).
7. Connect a short washing hose (C2) to washing liquid tank (C1) (PIC. 2.15) and to the connector at
the back of engine's set (PIC. 2.14).
8. Connect sucking hose (E5) to sucking inlet (B8) and sucking tubes (E9).
9. Connect fixing element (E2) to connector for a washing liquid hose (A3)
10. Connect washing tip (F1) to sucking tubes or directly to the handle. A tip for delicate cleaning (G1)
can be connected only to the handle. To wash carpets, rugs and to wash a floor use a normal tip.
To wash armchairs, sofas, curtains, car upholstery etc. use a tip for delicate wet cleaning, attaching
it directly to the handle.
11. Connect the device to the mains.
12. In order to switch on a pump press a pump switch (A1).
13. Press liquid feeder lever (E6). Water and shampoo (washing liquid) are pumped from a liquid con-
tainer with a pump and sprayed on cleaned surface with a tip. The liquid gets into fibres and dis-
solve even permanent dirt. Wait at least three minutes to let shampoo to be absorbed.
14. Switch off the pump with a switch (A1).
15. Press a vacuum cleaner switch (A2) in order to start sucking function and move the tip on the floor
surface. When washing upholstery, suction of dirty water and spraying of a liquid mixture may take
place at the same time.
16. If foam starts flowing from the container (B1) switch off the device immediately and empty the
container from dirty water. Also, check a quantity of washing liquid in a liquid container (C1). To
reduce the foaming add to the container (B1) a few drops of antifoam (H4).
WARNING! Never add antifoam agent to container (C1)
17. When the container is full of dirty water, the float will automatically block suction and the engine
will start to work louder. In such case, switch off the vacuum cleaner and the pump immediately,
take a plug from a socket, take a sucking hose (E5) from a handle (B8), and washing liquid hose (E3).
Take an engine's set off and empty the container.
18. If you want to clean hard floors, for example covered with tiles, marble etc put hard floors attach-
ment (F2) on a washing tip (F1). With the use of tip (F1) you can suck for example water which
has leaked from a dishwasher or washing machine or water left after fridge or freezer defrosting.
ATTENTION! Use of the vacuum cleaner that will be not-compliant with the instructions above,
may cause production of too big quantity of froth, which will overflow through HEPA filter. If
such thing happens, switch the device off, take the plug from a socket, empty the water contain-
er, clean water filter tank and dry it. Next take also HEPA filter out and dry it. Wash a foam filter
located in float section and leave it to dry. Wait about 2 hours to let froth from the engine dry off.

CLEANING AND MAINTENANCE

1. Before each cleaning, make sure that the device is disconnected from mains.
2. After every use, empty the water in the transparent water tank and clean and dry the tank. Do not
ever leave your vacuum cleaner with liquid and dirt in it for hygienic purposes and extending the
life of your vacuum cleaner.
34