DeWalt DCD444 Originalanweisung Seite 16

EnGLIsh
18V COMPACT STUD & JOIST DRILL
DCD444
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of this manual).
Technical Data
Voltage
Type
Battery type
No Load Speed
Max torque (Hard/Soft)
Chuck capacity
Max Capacity
Wood
Weight (without battery pack)
Noise values and vibration values (triax vector sum) according to EN62841‑2‑1:
L (emission sound pressure level)
PA
K (uncertainty for the given sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound level)
WA
Drilling into metal
Vibration emission value a
h,D
Uncertainty K =
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission level
represents the main applications of the tool. However, if the tool is
used for different applications, with different accessories or is poorly
maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise should
also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of work patterns.
16
V
DC
min‑1
Nm
mm
kg
dB(A)
dB(A)
dB(A)
dB(A)
= m/s 2
m/s 2
18V COMPACT STUD & JOIST DRILL
D WALT declares that these products described under
e
DCD444
Technical Data are in compliance with:
18
2006/42/EC, EN62841‑1:2015+A11:2022, EN62841‑2‑1:2018
1
+A11:2019+A1:2022+A12:2022.
These products also comply with Directive 2014/30/EU and
Li‑Ion
2011/65/EU. For more information, please contact D
0–1250
the following address or refer to the back of the manual.
233/37
The undersigned is responsible for compilation of the technical
13
file and makes this declaration on behalf of D
102
4.1
Markus Rompel
Vice President of Engineering, PTE‑Europe
85
D WALT, Richard‑Klinger‑Straße 11,
e
5
65509, Idstein, Germany
09.01.2024
93
a
5 WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
3.8
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
1.5
these symbols.

DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.

Denotes risk of electric shock.

Denotes risk of fire.
GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
EC‑Declaration of Conformity
Machinery Directive
DCD444
FOR FUTURE REFERENCE
WALT at
e
WALT.
e