Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6 OPERATION
Prior to switching on, set the master control and the output controls ZONE and BOOTH to zero to avoid
damage to the hearing by a volume which is too high when switching on. Switch on the mixer with the power
switch. Switch on the connected units. After operation, switch off the mixer with the power switch.
6.1 Basic adjustment of the input channels
1
First set all gain controls, equalizer controls and the crossfader to mid-position. Set the crossfader
assignment selectors to the position "M".
2
Use the input selector buttons to select the signal sources connected to the channels 1-3.
3
To control a channel, feed an audio signal (test signal or music piece) to the respective input channel
and advance the channel fader to approx. 2/3 of its maximum. Set all other channel faders to zero.
4
To monitor the signal via the speaker of a PA system connected, advance the corresponding output
control. The signal can also be monitored via headphones (please refer to section 6.5).
5
The level indication of the channel displays the signal level ahead of the channel fader (prefader level).
Via the level indication, control the level of the input with the gain control of the channel. An optimum
level control is obtained if level values in the 0 dB range are shown at average volume. If the red LEDs of
the meter light up, there is an overload of the channel.
6
Adjust the desired sound with the tone controls of the channel. By adjusting the three tone controls, the
high frequencies (control TREBLE), the midrange frequencies (control MIDDLE), and the low
frequencies (control BASS) can be boosted (12 dB max.) or substantially attenuated (26 dB max.). With
the controls in mid-position, the frequency response is not affected. Sound adjustments affect the level.
Readjust the channel level with the gain control, if necessary.
7
Repeat the steps for the other connected input channels as described above.
6.2 Basic adjustment of the output channels
The output signal is fed to the adjustable outputs MASTER, ZONE and BOOTH and to the recording output
REC(ORD) without individual level control.
1
Via the output meter, adjust the master signal to an optimum level with the master control. Usually an
optimum level control is obtained if the output meter shows values in the 0 dB range at average volume.
However, if the output level at the master output is too high for the following unit, the master signal must
be controlled to a corresponding lower level. If the output level is too low, it can be increased to 1.5 V
with the rear level selector switch.
2
Adjust the desired signal level for the output ZONE with the control ZONE.
3
Adjust the desired signal level for the output BOOTH with the control BOOTH.
4
The recording signal at the output REC(ORD) is taken off ahead of the output controls, i.e. it is not
affected by the master control and the output controls ZONE and BOOTH.
6.3 Crossfading between two channels/mixing the signal sources
1
Select the two signal sources for crossfading with the crossfader assignment selectors:
• position A: the channel is switched to side A
• position B: the channel is switched to side B
2
Set the faders of the channel not used to zero and control the two channels selected to an optimum level
with their faders.
3
Now crossfading between the two channels selected is possible:
• crossfader moved to the left: fade-in of side A and fade-out of side B
• crossfader moved to the right: fade-in of side B and fade-out of side A
• For hearing the signals of the two channels at the same level, set the crossfader to mid-position.
4
For mixing the signal of the other input channel to the music program, advance the fader accordingly.
5
If crossfading is not required, the connected audio sources can be switched directly to the master signal:
Set the corresponding assignment selectors to position "M" and adjust the desired volume ratio of the
audio sources with the channel faders.
The control X-FADER CURVE allows for continuous adjustment of the crossfading characteristic: Use
6
the left stop position for smooth crossfading e.g. for long mixes. The further the control is turned to the
right, the more abrupt the crossfading e.g. for scratching and cutting.
7
The switch X-FADER REVERSE allows reversing the assigned channels for the crossfader:
• upper position: the assigned channels are on their usual sides (control indicator off)
• lower position: the assigned channels are reversed (control indicator lights up)
27/31
00043092.DOC, Version 2.0
Werbung
Inhaltsverzeichnis
