Werbung
g
Stowin
lenshoodonthelens(Ref.Fig.(Til)
1 ) Revers
e
thelens hood. P oint t helens toward tie opening. thenalign thehood
attachi
ng
x
inde
onthelens with the(TAMRON
2 ) Tur
n
thehoo
d
e
clockwis
until t healignment mark (e)isatthetoptosetit.(Fig. [ flj)
.iN
'RESÄUT10fS
SfiöjtlüG
le optica
l
design forDiIItakes intoconsideration thevarious f eatures o fdigital s ingle
2fle
x
.
cameras
However, duetotheconfiguration o fthe digitalsinglereflexcameras, e ven
n
'he
theautofocus a ccurawiswithinspecificatlons, thefocalpointmaybea little
d
Irwar
or behind the optimum pont whenshooting with autofocusundersome
onditions.
imag
e
circles o fDiIIlenses aredesigned to match thedigital S LR cametzs using the
e
nag
sensor
s
t
equivalen
toAPS-C (approx. 15.5x 23.2mm). DonotuseDi'l lenses with
amera
s
usingimagesensors largerthanAPS-C. UsingDiIt lenses with suchcameras
causevignettingon the image.
h e Tamro
n
lenses described hereemployan internal focusing(IF)system. B ecause of the
s
haracteristic
ofthisoptical d esign, t he angles otviewat distances otherthaninfinityare
ider than that of the tensesapplyingan ordinaryfocusing system.
menthe built-in flash on the camera is used, adversephotographic phenomenasuch as
orne
r
illuminatio
n
fall-offorvignetting a tthebottom partoftheimage maybeobserved,
y
speciall
inwideangle ranges. Thisisduetotheinherent 'Imitation o fthecoverage of
built-inflash and/or the relativeposltEon o f theflashto the edgeofthe tensbarret
h
Ihic
causes shadows on theimage.It is strongly recommended t ousea suitable
e
eparat
flashunitprovided b ythecamera m anufacturer forallflashphotography.
oriuitherdetails
,
please read the"built-in flash"article ontheinsuuction m anual ofyourcamera.
"he
n
usingthe lensin the telephotofocalrange,pteasebe carefulof camerashake.
0 reduceimageblur,turnthe VC(Vibration Compensation) switch on.
Oreduceimageblurwithout usingthe VCfunction,follow the stepsbelow.
o avoidcamerashakeon digitalcameras,use higherISOsettingandtor film
ameras
,
use higheriSOfilm to obtainhighershutterspeeds.Usinga tripod or
d
nonopo
is alsoeffective.
Vhe
n
hand-
holding
thecamera tc takepictures, s tand still openjng yourlegsslightly
part, hold yourelbowsin firmly againstyourChest, a ndh01d the camerafirmly
gainstyourface.if possible, l eanagainstsomethingto steadyyourselfor Placethe
ameraon something to securethe hold. Especially whenhand-holdingyourcamera,
o u will besteadierif you holdyourbreathwhile you pressthe shutterbuttongentEy
nd firmly.
thenseton AFmode,interfering with focusing ringmaycause serious damage to the
ens mechanism.
;ertai
n
camera mode(s mayindicate themaximum andminimum aperture valuescf the
en
s in approximat
e
numbers. Thisisinherent t o thedesign cf thecamera andnotan
Ndjcation of an error.
e
leas
beawaretlat thereis noinfraredindexlineon anymodels listedin thisowner's
E,
nanua
andtherefore, practically, noblack-and- whiteinfrared film canbe usedwith
nese lenses.
"he
n
usingaspecial f iltersuchasa PLfilter,uselow profilefilters.Thethickrim ofa
lormalfilter may causevignetting,
ivcidtouching the glasselement s urface. U sea photographic l ensctothor blower to
emove dust from the lens elementsurface.Whennot using lhe lens, always placea iens
ap on it for protection.
Is e alensdeaning tisue or lintclothwitha dropof cleanlng solution to remove fingerprints
i r dirtontheglass lenssurface
a rotarymotion fromthecenter t o theedge.
kea SiliconCi0thto creanyour lens barrelonly.
nilde
w
is anenemy of yourlens.Clean the lensaftershooting nearwateror in anyhumid
.
)lace
Storeyourlensin a clean,coolanddry place.When s toringthelensin an lenscase,
;tore it with commerchlly availabledrying agentsuch as silicagel,and changethe agent
.
xcasionally
If youfind mildewon yourlens,consult a n authorized r epairshopor nearby
)hotographic store.
not touch the lens-camerainterfacecontactssince dust,dirt and/orstains may causea
:cntact failure between the lens and camera.
Nhe
n
usingyour equipment[camera(s)and
emperaturechangesfrom one enreme to the other,make sure to put your equipment
emporarjlYin a caseor a plasticbag for a lengthof time in order for the equipmentto go
nrough a graddaltemperatureshift. This will reducepotentialequipment trouble.
O)a'ignment ontheh00d 0),
in an environmentwherethe
Werbung
