Technical Data; Before Starting The Equipment - EINHELL TE-OS 18/1 Li Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 18 V DC
Idling speed .......................................12000 min
Sanding area: ..................... 150 x 150 x 100 mm
Abrasive paper size
(Velcro fastening system): ...... 93 x 60 x 105 mm
Oscillatory circuit Ø: ................................ 1.6 mm
Battery charger output voltage: .............. 21 V DC
Battery charger output current: ....................... 3 A
Charging unit
supply voltage: ................... 200-260V~ 50-60Hz
Battery type: ...................................... Lithium-ion
Number of battery cells: ................................... 5
Battery capacitance: ................................. 1.5 Ah
Weight: .......................................................0.7 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 77.2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 88.2 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_TE_OS_18_1_Li_SPK7.indb 17 Anl_TE_OS_18_1_Li_SPK7.indb 17
-1
= 6.585 m/s
2
h
2
- 17 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger. An
empty battery pack requires a charging peri-
od of approximately 0.5 to 1 hour.
5.1 Fitting the dust collection box (Fig. 2-3/
Item 4)
•
Plug the dust collection box (4) onto the vacu-
um cleaner connector (a).
•
The dust is extracted directly into the dust
collection box through the abrasive paper and
the oscillating plate (5).
15.11.2016 07:09:19 15.11.2016 07:09:19