Bauknecht BIK5S DP8F2 ES Bedienungsanleitung Seite 24

with a countdown indicating the status of the cycle
in progress. Once the cycle has been completed, the
door remains locked until the temperature inside the
oven has returned to a safe level.
Please note: remove water from the drawer before pyro
cycle activation
•
DRAIN
The drain function allows the water to be drained in
order to prevent stagnation in the boiler. This product
has been developed in order to automatically run
a drain cycle once cooking has been stopped/has
ended. Approximately 30min after the stop/end of
cooking, the oven will automatically drain the system,
moving the residual water in the drawer (be careful
not to remove the drawer after cooking). Once done,
the drawer can be extracted and emptied.
We recommend emptying the drawer as soon as the
drain is completed, after the cooking cycle.
If needed, a manual drain can in any case be executed
by the user following the instruction below.
Please note: to ensure that the water is cold, it is not
possible to perform this activity before 30 minutes have
elapsed from the last cycle (or the last time the product
was powered). During this waiting time, the display will
show the following feedback "WATER IS HOT"
• DESCALE
This special function, activated at regular intervals,
allows you to keep the steam system in the best
condition. Once the function is started, follow all the
steps indicated on the display and press
done to start each phase. The average duration of the
full function is around 100 minutes.
Please note: If the function is stopped at any time, the
entire descaling cycle must be repeated.
The display will show you when it is time to run a
Descale cycle (see the table below).
DESCALE MESSAGE
<RECOMMENDED DESCALE>
It appears after around 15 hours of
steam cycles*
<PLEASE DESCALE>
It appears after around 20 hours of
steam cycles*
*considering the default value (4 - Hard) of water hardness
level. The number of hours of steam cycles that must pass
before the Decale messages are shown depends on the
water hardness level set on the appliance.
Select the "Drain" function
with the water drawer properly
inserted in the oven, press
and wait for the cycle
to automatically run. The
average duration for full load
drainage is about one minute.
Once done, the drawer can be
extracted and emptied.
MEANING
It is recommended to run a
Descale cycle.
Descale is mandatory. It is
not possible to run a Steam
cycle until a Descale cycle
will be carried out.
The descaling procedure can also be performed whenever
the user desires a deeper cleaning of the internal steam
circuit.
Before to run the descaling phase, the appliance
will check if some residual water is contained into
the boiler, and a Drain cycle could be performed,
if needed. In this case, you will have to empty the
drawer after the Drain cycle, before continuing with
the Descale Phase.
Please note: to ensure that the water is cold, it is not possible
to perform this activity before 30 minutes have elapsed from
the last cycle (or the last time the product was powered).
During this waiting time, the display will show the following
feedback "WATER IS HOT".
PHASE 1/2: DESCALING 70 MIN
When display will show <ADD 0.25 L OF SOLUTION>,
please pour the descaling solution in the drawer. For
best results in descaling, we recommend filling the
tank with a solution composed of 75 g of the specific
WPRO product and 250 ml of drinking water. Make
sure the solution dissolves completely in the water
so that no residue remains. WPRO descaler is the
suggested professional product for the maintenance
of the best performance of your steam function in the
oven. For orders and information contact the after
sales service or www.bauknecht.eu. Whirlpool will
not be held responsible for any damage caused by
the use of other cleaning products available on the
market.
when
Once the descaling solution is poured inside the
drawer, press
The descaling phases do not need you to stay in front
of the appliance. After each phase is completed, an
acoustical feedback will be played and the display
will show instructions to proceed with the next
phase.
Once the descaling phase has been completed, the
boiler will be drained: the descaling solution used
during this phase will be poured into the extractable
drawer.
PHASE 2/2: RINSING (30 min.)
To remove descale residuals from the drawer and the
steam circuit, rinse cycle has to be done. When display
shows <ADD 0.25 L OF WATER> fill the tank with 0,25 L
of drinking water, then press
not turn off the oven until all the steps required by the
function have been completed.
= 75 g
1 + 2 +
250 ml
to start the main descaling process.
to start the rinsing. Do
3