Werbung
Verfügbare Sprachen
Verfügbare Sprachen
only when the oven is heavily soiled.
•
DRAIN
For draining the boiler in order to prevent residual
water remaining in there when the appliance will
not be used for a certain period of time.
•
DESCALE
For removing limescale deposits from the boiler.
We recommend using this function at regular
intervals. If you do not, a message will appear on
the display reminding you to clean the oven.
•
DIAMOND CLEAN
The action of the steam released during this
special low-temperature cleaning cycle allows
dirt and food residues to be removed with ease.
Pour 200 ml of drinking water on the bottom of
the oven and only activate the function when the
oven is cold.
FIRST TIME USE
1. SELECT THE LANGUAGE
You will need to set the language and the time
when you switch on the appliance for the first time:
"English" will show on the display.
English
Press
or
to scroll through the list of available
languages and select the one you require.
Press
to confirm your selection.
Please note: The language can subsequently be changed
by selecting "LANGUAGE" in "SETTINGS" menu, available by
pressing
.
2. SET THE POWER CONSUMPTION
The oven is programmed to consume a level of
electrical power that is compatible with a domestic
network that has a rating of more than 3 kW (16): If
your household uses a lower power, you will need to
decrease this value (13).
POWER
Press
or
to select 16 "High" or 13 "Low" and press
to confirm.
3. SET THE TIME
After selecting the power, you will need to set the
current time: The two digits for the hour will flash on
the display.
CLOCK
Press
or
to set the current hour and press
two digits for the minutes will flash on the display.
MINUTEMINDER
For keeping time without activating a function.
SETTINGS
For adjusting the oven settings.
When "ECO" mode is active the brightness of the display
will be reduced to save energy and lamp switches o after
1 minute. It will be reactivated automatically whenever any
of the buttons are pressed.When "DEMO" is "On" all
commands are active and menus available but the oven
doesn't heat up. To deactivate this mode, access "DEMO"
from "SETTINGS" menu and select "O ".
By selecting "FACTORY RESET", the product switches o and
then it returns to rst switch on. All settings will be deleted.
Press
or
to set the minutes and press
confirm.
Please note: You may need to set the time again following
lengthy power outages. Select "CLOCK" in "SETTINGS"
menu, available by pressing
. SET THE WATER HARDNESS LEVEL
In order to allow the oven to work e ciently, and
to guarantee that it regularly prompts the user to
perform Descale cycle when needed, it is important
to set the correct water hardness level. To set it, switch
on the oven by pressing
use navigation buttons
HARDNESS". Press
buttons
and
water of your area, based on the following table:
WATER HARDNESS LEVELS TABLE
Level
1
Very soft
2
Soft
3
Mid
4
Hard
5
Very hard
Press
to confirm.
For Water Hardness level, "Hard" is preset.
5. HEAT THE OVEN
A new oven may release odours that have been left
behind during manufacturing: this is completely
normal.
Before starting to cook food, we therefore
recommend heating the oven with it empty in
: The
order to remove any possible odours. Remove any
protective cardboard or transparent film from the
.
, press Settings
and
to select "WATER
to con rm. Use navigation
to select the correct level for the
°dH
°fH
German
French
degrees
degrees
0-6
0-10
7-11
11-20
12-16
21-29
17-34
30-60
35-50
61-90
to
and
°Clark
English
degrees
0-7
8-14
15-20
21-42
43-62
Werbung
