Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CAS1000R-RGB-EU products, the Bluetooth receiver (Fig 9) should be connected to the 'master' product.
3.
Plug the daisy chain link wire into the connector on the right hand side of the first/'master' module (Fig 20B, 21B).
4.
Feed the wire through the hole in the metalwork and into the housing of the next product in the installation.
5.
Plug the daisy chain link wire into the left hand connector on the RGB strip on the following product (Fig 20C, 21C).
6.
Each product is fitted with a rotary identifier switch which must be adjuted for daisy chaining (Fig 22). The master
unit should be set at 0 (default). Subsequent units should be given a unique identifier number on each binary switch.
7.
Repeat steps 3-6 above in order to connect subsequent products in the installation.
Once set up, any command sent to the first product will be sent to all subsequent products. Flame height control and
sound level control of the master product is matched for all subsequent products. If individual flame height control is
required, this can be done by using the on board flame height controls on the product (Fig 23).
Additionally, the software of the product has been designed in such a way that when multiple products are connected
to a main switch, products can be manually switched off and when switched back on they will operate in the same state
as before they were switched off.
OPERATING THE PRODUCT
This section describes how to activate your fire using either the manual controls or remote control.
MAINS SWITCH
The mains switch is located under the fuel bed on the module and controls the electricity to the appliance (Fig 23A).
Note: This switch must be in the 'ON' ( I ) position for each appliance to operate.
MANUAL CONTROLS
Manual controls are located on the cassette module under the fuel bed. There are also manual controls on the tethered
receiver unit which is fitted loose.
REMOTE CONTROL
The remote control is supplied with 2x CR2032 batteries already fitted. Pull both tabs from the rear cover to engage the
batteries (Fig 24) and allow remote operation.
Note: The tethered receiver must be fitted to the product for remote control operation.
PAIRING THE REMOTE CONTROL
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1.
Press the rocker switch to the on (I) position.
2.
Press the
button on the Button Panel; the product will turn on.
3.
Press the
button on the Button Panel, the LED's will start to slowly blink on and off.
4.
Press the
button on the remote control; the product LEDs will flash quickly five times and the product will then
automatically switch off. The remote control is now paired to the product and can be used to switch it back on.
TO REPLACE THE BATTERIES
1.
Remove battery cover of the remote control using a Philips screwdriver (Fig 25).
2.
Correctly install two 3 Volt (CR2032 or similar) battery in the battery holder with the + side facing up .
3.
Secure the battery cover using the previously removed screw.
Batteries must be recycled or disposed of properly.
Check with your Local Authority or Retailer for recycling advice in your area .
Frequency band(s) this product operates in: 2.4GHz
Maximum radio-frequency power transmitter in the frequency band(s) this product operates in: 8.23dBm
CREATING YOUR PERFECT OPTIMYST EFFECT
With Optimyst technology you can create a flame effect that is unique to you. First ensure the appliance is on by pressing
the main switch to I (Fig 10). To turn on the flames press the
the ENTER button to activate and use the
FLAME COLOUR: There are 6 colour themes to chose from. To adjust the flame colour, navigate to colour icon
the remote and press enter. Use
manual controls press the
TIP: Orange is the go to colour for a traditional authentic look, but when it is time for a celebration switch to the Prism
theme that cycles through a rainbow of colours. In summer time blue is both cooling and calm, whilst green always
draws attention at Holloween.
or
buttons to navigate to the
or
to toggle between options 1 to 6 flame themes and ENTER to select. On the
repeatedly to cycle through the colours.
button on the manual controls. If using the remote, press
icon and press ENTER to select.
7
on
Werbung
