Makita E UC3020A Bedienungsanleitung Seite 7

Caution: particular care and attention
➬
required!
Caution: withdraw the mains plug
➬
immediately if the cable is damaged!
Caution: kickback!
➬
Protect against rain and damp!
➬
Wear a helmet, goggles and ear
➬
protection!
Wear safety gloves!
➬
Withdraw the mains plug!
➬
First aid
➬
Recycling
➬
CE marking
➬
Maximum permissible length of cut
➬
Direction of chain travel
➬
Chain oil
➬
Chain brake released/applied
➬
Prohibited!
➬
Only for EU countries
➬
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an
recycling facility.
Intended use
The tool is intended for cutting lumbers and logs.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
equipment and
environmentally compatible
to the operation of other equipment. With a mains
impedance equal or less than 0.35 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
EC-DECLARATION OF CONFORMITY
The undersigned, Kato, as authorized by, declare that
the MAKITA machines,
Type:
211
EU model identification No.:
UC3020A, UC3520A, UC4020A:M6 05 10 24243 064
complies
requirements of the pertinent EU guidelines:
EU machinery guideline 98/37/EC, EU EMC guideline
2004/108/EC, Noise emission 2000/14/EG.
The requirements of the above EU guidelines were
implemented chiefly on the basis of the following
standards: EN60745-2-13, EN55014-1, EN55014-2,
EN61000-3-2,
assessment procedure 2000/14/EG was performed per
Annex V. The measured sound power level (Lwa) is 100
dB(A). The guaranteed sound power level (Ld) is 101
dB(A). The EU Type-Examination per 98/37/EG was
performed
Zertifizierungsstelle, Ridlerstra e 31, D-80339 M nchen.
000230
Responsible Manufacturer:
its
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
ENE031-1
Chain saw safety warnings:
DO NOT let comfort or familiarity with product
ENF002-1
(gained from repeated use) replace strict adherence
to chain saw safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
1. Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
ENF100-1
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
6
with the standard
EN61000-3-3.
by: TUV Product
CE2007
Tomoyasu Kato
Director
ENH016-4
safety and health
The conformity
Service GmbH,
GEB037-3