Repair Service - ROBBE-Futaba F-14 Bedienungsanleitung

the adjustment control should simply be turned in the other
direction. When the control is in the neutral setting, the
control function has no effect.
Combi Switch: In order to be able to influence the rudder at
the same time as you operatethe aileron, plug the leadsof
thecontrol f unctionsontothecorresponding s ocket p inson
the minioption, plug the leadsfrom the minioption intothe
STICK sockets on the transmitter electronics board. Connect
the additionalmixerswitch to thecorrespondingsocket,do
not switch on the main switch. Turn the adjustment control
in one direction. If, upon operating one function, there is no
deflection of the other function, then the additional switch
should be switched ON. The level of influence can now be
set, using the adjustment control. If the wrong function is
influenced(therudderinfluencestheaileron),thentheAugs
of the control functions must be changed over on the mini
option. If the direction of influence is wrong, then the
corresponding control should be rotated in the other direction.
Y-iead: In order to have two servo outputs on the receiver
for one control channel , simply plug the lead of the required
control function onto one of the pin sockets on the mini
option. Both leads from the mini option are then plugged into
the free ST 10K socket
transmitter, the servos
corresponding transmitter outputs.
Switch on the mini option's
adjustmentcontrol in one direction. Ifthe function runs in the
wrong direction, rotate the corresponding plug at the STICK
or EXT. socket through 180' If the direction of influence is
wrong, turn the adjustment control in the other direction
on the transmitter electronics board. If only one MULTI-
module is used, then only the corresponding MIJLTI
adapter pfug need be pushed into one of the EXT or
STICK sockets on the electronics
Connection of
module
The white MULTI„moduIeplug with the triple-thickness
lead should be plugged into the white,three-pinMULTI-
adaptersocket.The black MULT\-module plug with a
one-pin lead should be plugged crosswiseinto the
white connection pins. On the receiver, the MULTI-
decoder must be connected to the receiver outputs,
which must correspondwith the EXT. or STICK sockets
in which the MULTI-modules
meansof the MULTI-adapter.For every MULTI-switch/
prop unit which is installed, a MULTI-switch/prop
decoder must also be connected to the receiver.
Transmitter Tray
Usin g thetransmitter t raywhichis an optional a ccessory
r (Orde No.F 1514), t hetransmitter canhangcomfortably
aroundtheneck,causingnofatigue.Inconjunction withthe
lon g stick grips, t hisprovides aparticularly sensitive m ethod
of controls.

14. Repair Service

For optimum results, please take the following steps prior to
requesting repairs:
and a free EXT socket.
should be installed
main switch and turn the
board
MULTI-switch/prop
have been connected by
Muktiswitch/Mu\tiprop
By means of these programmes, one function can be
divided into 8 proportional or switch functions. A maximum
of 2 multiprop or 3 multiswitch modules can be installed in
the transmitter at any one time (they can, of course, be
mixed). This makesthe transmitter ideal for aumodelship
applications,or in any other areas which demand a large
number of functions
installation:
in such a way that the 3-pin socket on the soldered side of
the multi module faces the inside of the transmitter (not
towards the outer edge of the transmitter case). The third
block is installed in option well 3 under the battery box,
facingthedirectionshown.Beforeinstallation,removeF-14
protective film from the front plate of the transmitter and
apply new protective film in which holes have been made
To be able to install a MULTI-switch/prop module in the
F-14 transmitter, the MULTI-adapter, Order No. F 1561
must also be installed
MULTI-switch/prop
MULTI-adapter.
not work in the F-i 4 without the MULTI-adapter.
Installation
MULTI-adapter
On the
at the
Using the enclosed
MULTi-adapter
holder). The white MULTi-adapter plug with 4-thickness
lead should be pushed into the MULTI-OP socket on the
transmitter
single-thickness
18
Chargebatteries prior to dispatchingfor repair.
Send only the radio control set, not the entire model.
2
Any extensions fitted (e.g. servo plugs)will be restored
3
to their original condition against payment.
Make sure that all parts are securely packed - the
4.
original packing is best.
A brief, but precise description of defects Wii!help us to
5.
locate the fault more quickly, thus saving time and
money.
Please enclose a list of contents in the package to assist
6
us in ensuring that everythinghas been received.
SERVICE ADDRESS:
robbe Modeitsport GmbH
Abteilung Service
Postfach 1 108
6424 Grebenhain
West Germany
15. Crown
Thecrowngearservoleverfacilitatesmechanical a djustment
of the neutral servo position. Setting neutral position:
Remove retainingscrewof drivinglever,liftoff lever,refitin
required neutral position and re-tightenscrew. Effect: For
thesmallestpossible adjustment(3.60)to the RIGHT,ARM
2 of the 4-armed servo lever must be placed on the closest
possibleposition of base Eine so that ARM3 is adjustedby
7.20 and ARM 4 by 10.80. For the smatlest possible
adjustment to theLEFT(3.6'),ARM4 mustbeplaced onthe
next position of base line.
Subject to correction, changes in supply and technicai
specification.
Moduie
The blocks must be installed
in the transmitter.
modules can be connected
The MULTI-switch/prop
and connection
screws, instal
in its correct place (under the battery
electronics board. Push the black plugs with
leads into the EXT. or STICK sockets
i
Gear Servo Lever
in the transmitter
A maximum of 3
to this
modules do
of
and secure the