Denon DRM-740 Bedienungsanleitung Seite 6

ENGLISH
SYNCHRONIZED RECORDING FUNCTION
e Convenient synchronized recording can be performed when used in
combination with a DENON CD player equipped for the synchronized
recording function.
e SYNCHRO Jack Connection Connect the SYNCHRO Jack with a DENON
CD player which is equipped with a SYNCHRO jack, then make a
synchronized recording. Use the connection cord supplied with this
cassette deck.
e Switch on your amplifier or receiver and the CD player.
e Setthe tape Monitor switch on your amplifier or receiver to the source
position.
@ Load the tape, the disc you want to record into the CD player.
Q Following the recording instructions on page 9, set the Dolby NR mode,
and the input level.
(3) Set the CD player to the stop or pause mode.
(0) Press the REC/REC MUTE (6) button ® and REC PAUSE ( II ) button ®
simultaneously. The cassette deck and CD player are automatically set
to the synchronized recording mode. The "ІШ" indicator flashes on the
cassette deck and the synchronized recording mode is indicated on the
CD player.
(For details, refer to the CD player's operating instructions.)
( To stop synchronized recording, press the stop button.
The synchronized recording mode is cancelled for both the cassette
deck and CD player.
© To stop synchronized recording temporarily, press the stop button on
the CD player. A 5-second blank space is created on the tape, after
which the recording pause mode is set. The "Bi" indicator flashes.
To resume synchronized recording, press the PLAY button on the CD
player.
TAPE COUNTER AND MEMORY STOP
CD player
Power supply outlet;
1
Cassette deck
Note:
e If synchronized recording is started when the CD player is in a mode
other than the stop or pause mode or when no disc is set, the "MW"
indicator on the cassette deck flashes and the recording pause mode is
set until synchronized recording is possible on the CD player.
e In the synchronized recording mode, only the STOP button will
function.
Caution:
e Do not set the cassette deck to the synchronized recording mode when
the CD player is in the play mode. Also, do not turn off the power of the
cassette deck or the CD player during synchronized recording. Doing so
can result in malfunction.
e During the editing operation, when using the editing functions on the
CD player, be sure to select a tape with a sufficiently long recording
time.
For the CD player's editing functions, refer to the CD player's operating
instructions.
db 40 -30 -20 15 -10 -7 -5 3 24 0 +1 +3 +5 +8 +10
t 00000000000: 0000000000
REMOTE SENSOR
CD SYNCHRO
Ш 25 H H H H MEMORY r5 "S
00000000000
TAPE
DOM
—— B MUSIC SEARCH —
1) Operation of the Tape Counter
(1) Press the RESET button O to reset the " 00.00 "
(2) By using the PLAY, ҒҒ, or REW function, the reading of the counter
indicate in minutes and seconds.
e During recording and playback operations, the counter is useful for
noting the location of existing programs or positions where
recording is to be started.
e The reading of this counter does not correspond with that of any
other deck.
e The linear counter of this machine is designed to be suitable for the
cassette tape with a small hub.
Therefore if a cassette tape with a large hub is used is this machine,
some error will occur in the display on the counter.
10
2) MEMORY STOP Operation
(1) During recording or playback operations, MEMORY STOP can be
used to locate a particular point on the tape. At the desired point,
reset the counter to " 00.00 *. With the MEMORY STOP button Ө
in the "ON" position, the deck will stop at the " 00.00 " point ,
(actually " —00.0? " and " 00.00 ") during REWIND operations.
(2) The MEMORY indication will light when this function is activated.
(3) Notes:
e When the power is turned "OFF", this function is automatically
deactivated.
e The MEMORY STOP is accurate to —5 on the counter, and will stop
between " —00.0? " and " 00.00 ".
e The MEMORY STOP is released by pressing the EJECT button (B.
e The MEMORY STOP does not operate during the REC RECTURN.
3) Display Back-up
(1) The functions DOLBY NR, MPX FILTER, MONITOR and TAPE SIZE
are protected by 24-hour memory back-up.
After 24 hours, DOLBY NR and MPX FILTER are set to "OFF",
MONITOR is reset to "TAPE", TAPE SIZE is reset to "C-90".
Cassette Deck adopts an automonitor system, or
also be activated manually.
Recording
Playback
Monitor button => [TAPE ]
^ Tape
Rec Head P/B Head
Monitor button => [ SOURCE ]
x
Tape A
Input Output
Monitor button => [TAPE ]
Tape I
\
| H P/B Head
Output
MONITOR BUTTON PT m L a L
This Stereo cassette deck uses a three-head system which permits simultaneous "off-the-tape monitoring" during recording. Incidentally, as this Stereo
can automatically be activated according to the operation conditions. These modes can
The signal recorded on the tape is monitored simultaneously "off-the-tape". This monitoring
mode enables you easy check for optimum recording levels. In the mode, the FL PEAK
METER indicates the signal levels played back off-the-tape.
The [SOURCE ] position enables you to monitor the input source signal before it is recorded on
the tape. Using the FL PEAK METER, this mode is convenient for setting recording levels or
input level monitoring during recording.
During playback, the MONITOR button must be placed in the position. If it is set in the
SOURCE position, the signal from the tape won't be heard.
11