Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
NAMES AND FUNCTIONS OF PARTS
POWER
switch
Controls the supply of AC power to the deck. One push turns the
deck on, a second push turns it off. The deck remains in a stand-by
(non-operative)
mode
for approximately
2 seconds
after it is
switched
on.
PHONES
jack
For private music
enjoyment
without
disturbing
others, or for
monitoring a recording, a set of headphones may be plugged in.
Impedance should be from 8 to 1200 ohms.
COUNTER
RESET button
Operation
of the button
resets the counter
to all zero.
MEMORY
STOP button
During rewinding operations, the tape will stop at the " 0000
"
counter
point automatically
when
this button
is pressed
in.
TAPE SIZE button
You can know accurate elapsed time of the tape by adjusting the
TAPE SIZE button to the tape size used.
When the TAPE SIZE button is pressed, the current tape size is
displayed for 1 sec in the 4-figures counter. If you further press the
button during the display, the tape size will change in the following
cycle.
C-90 C-75 C-60 C-100
DOLBY
NR button
When the left-side DOLBY NR button is pressed once with DOLBY
NR being at the "ON" state. DOLBY NR B-TYPE is preferred and
turned on. Every time when the rightside B/C button is pressed,
B-TYPE and C-TYPE are selected alternatively.
REC RETURN
button
When
this button is pressed at the recording state, the tape is
rewound to the starting point. When the starting point is automati-
cally reached, the record standby mode
(rec pause state) comes.
BIAS control
(for NORMAL,
CrO; and
METAL
tape)
Adjust the bias according to the tape characteristics.
Standard
biasing
is obtained
at the center click-stop position.
MONITOR
button
The SOURCE
position of this button allows you to monitor the
source program
before it is recorded. The TAPE position of this
button
is used
for tape playback
monitoring
or simultaneous
monitoring during recording.
BALANCE
control
This is the knob to adjust the recording level balance between the
left and right channels. Turn it counter-clockwise to reduce the right
channel's level and clockwise to reduce the left channel's. Usually,
put the knob
at the center click position.
OUTPUT
LEVEL control
This control adjusts playback, recording monitor, and headphones
output
levels for the both channels
simultaneously.
e e e е e e ее
8 e 8 e
MPX filter button
The MPX FILTER button should be used to prevent interference with
the Dolby NR circuit when making Dolby NR encoded recordings of
FM
stereo
programs.
When
making Dolby NR encoded recordings from any program
source
other than
FM
stereo,
leave this button
in the "OFF"
position.
EJECT
button
Press this button to eject the cassette. When the deck is operating
(tape is running), press the stop ( lll ) button first to stop the tape
transport; then press the EJECT button.
Cassette compartment
cover
If this compartment
cover is not closed completely, the deck's
transport
controls
will remain
inoperative.
PLAY, PAUSE and REC indicator
When the PLAY, REC PAUSE and REC buttons are pressed, this
indicator will light.
Fluorescent
peak meters
These meters indicate recording or playback peak levels for each
channel.
For peak levels exceeding
—7dB, the Auto Peak Hold
Feature holds the peak level reading for approximately 1 seconds.
Linear tape counter
Tape-passage
is indicated
digitally in minutes
and
seconds.
MEMORY
Indicator
This indicator light is interlocked with the memory
stop button.
(MEMORY)
FILTER indicator
This indicator light is interlocked with the MPX
FILTER
button.
(FILTER)
NR system indicator
This indicator light is interlocked with the DOLBY NR button and
informs the user that DOLBY NR is in use as well as which B-TYPE or
C-TYPE.
TAPE SELECT indicator
This indicator light is interlocked with the Auto Tape Select feature
which
automatically
adjusts the deck to the type of tape in use.
(TYPE
I TYPE
Il or TYPE
IV).
MONITOR
indicator
This indicator light is interlocked with the MONITOR
button to
inform
the use of the selected
monitoring
source
— TAPE
or
SOURCE.
INPUT LEVEL control
The recording input level is adjusted by this knob. The levels in the
left and right channels can be changed simultaneously.
REMOTE
SENSOR
This sensor receives the infrared light transmitted from the wireless
remote
control
unit.
For remote control point the wireless remote control unit at the
sensor.
ENGLIS
Ф
Tape transport controls
» PLAY
Play button
Press to playback
tape.
Ш STOP
Press to stop tape in any mode.
button is pressed for making a non-recorded
part between two melodies, about 5 sec of
Press for fast forward tape winding.
e REC/REC
MUTE
non-recorded
part can
automatically
be created.
To begin recording, press the RECORD and PLAY button simultaneously. If only the RECORD
Press this button to enter the recording pause mode from the recording
or recording mute
H PAUSE
PAUSE button
mode. Press this button to enter the playback pause mode from playback mode.
button is pressed, the deck is placed in the REC PAUSE (record standby) mode. When this
button is pressed under the REC PAUSE state, the mode shifts to the Auto
Rec Mute. When this
RECORD/MUTE
button
CASSETTE TAPES
Ш Handling
Precautions
Ш Storage Precautions
e
C-120 cassettes
e
Do not store cassette tapes in a place where they will be subject to:
C-120 cassette are not recommended as they use a very thin tape base
which may become tangled around the capstan or pinchroller.
e
Tape slack
e Direct sunlight
This cassette deck incorporates an automatic tape slackness preventive
e Magnetic fields (near TV sets or speakers)
_ mechanism,
but it can not prevent such a slackness as shown
below.
e
To eliminate tape slack, store your cassettes in cassette cases with hub
Remove
it with a pencil or the like prior to use.
stops.
e Extremely
high temperature
or excessive
moisture
e Excessive
dust
Ш Accidental Erasure Prevention
Every cassette has erasure prevention tabs for each side.
To protect your valuable recorded tapes from accidental or inadvertent
erasure, remove the tab for the appropriate side with a screwdriver or
other tools.
e
To record on a tape with the erasure prevention tabs removed, cover
the tab holes with plastic tape.
Erasure prevention tab for side B
AUTO TAPE SELECT FEATURE
This Stereo Cassette Deck contains an Auto Tape Select feature which
automatically selects the optimum bias and equalization for the tape in use.
e
Ifa tape without tape type detection holes is used, the deck will
This is accomplished by detection of tape type detection holes in the
automatically adjust itself for normal tapes.
cassette housing.
Detection holes
for metal tape
Detection holes for
chrome
tape
Werbung
